User guide

142
DPP Commands continue
Processor Activity:
>SWACT o Change current active processor (A to B or
B to A).
o = FORCE: optional entry
reset any alarms on the standby processor
and then performs the SWACT.
Site Data Entry:
>
AMAHRS Displays hour boundaries currently assigned.
>AMAHRS s e Set the time interval to verify
that AMA records have been received from the
Switching System.
s = two digit start time(00 - 23).
e = two digit end time (00 - 23).
>
AMATPSW Examine the AMAT Password.
>AMATPSW t i Change AMAT password.
t = 4 digit sensor type
i = 6 digit sensor id
>
BX25PARM PRIHDR Displays the current AMATPS requirements.
>BX25PARM p Change the AMATPS parameter.
P = PRIHRD1 = 1986 AMATPS requirement.
PRIHRD2 = 1990 AMATPS requirement.
>BAUD Displays current polling baud rate for
the link on NON-TURBO or Links 1 & 2 for
TURBO DPPs.
>BAUD r Change polling baud rate for the NON-TURBO link.
r = baud rate: 1200/2400/4800/9600.
Polling link NON- TURBO is J1
>BAUD l r Change polling baud rate for the TURBO
links 1 & 2.
l = link: 1 or 2.
r = baud rate: 1200/2400/4800/9600/56K.
Link 1 = J11 for 56K polling, J13 for 1200 thru 9600 baud polling.
Link 2 = J12 for 56K polling, J14 for 1200 thru 9600 baud polling.
>COLLPSW Displays current collector password.
>COLLPSW # t i Change the collector password.
# = Collector Password #:1, 2
t = 4 character office type.
i =6 character office id.
>SITDAT READ Reads (restores) the site data parameters
from the DPP disk and over writes the main
memory (RAM).
>SITDAT WRITE Updates (Saves) the site data parameters
from memory to disk.
>VALPARM BLOCKS Displays the minimum number of blocks
needed in the open write AMACRD file
before the file is closed at the begining
of a primary poll.
>VALPARM BLOCKS x Change the minimum block number.
x = 1-999 (default is 200).
>VALPARM INVALID Displays invalid blk quantity threshold
value currently assigned.
>VALPARM INVALID b Change invalid blk quantity threshold.
b = number of blocks:0-65535
>VALPARM LOGHDR Displays current status of the log header
either enabled or disabled.
>VALPARM LOGHDR x Enables or Disables the display of the
block header as they are written to disk.
x = ON/OFF
Program Versions:
>CP VS s Displays the selected 56K Comm processor
software program version ID and firmware
version ID.
s = ACT or STDBY
Note: CP command is for TURBO DPPs only.
>DISK VS Displays the disk firmware version ID.
>DSIMAINT SHOW x VS Displays the active processor firmware
verson ID for the selected DSI.
>DOS S DSIMAINT SHOW x VS
Displays the standby processor firmware
verson ID for the selected DSI.
x = DSI Port ID: 1 or 2.
= 1 = DSI in slot A13
= 2 = DSI in slot A12.
>VS s Displays the selected processor software
program version ID and firmware version ID.
s = ACT or STDBY
Statistics:
>AMATSTAT Displays a summarized status report of AMAT
records on DPP disks.
>CLRSTATS Clears today’s statistics file reports.
>REPORT t p Displays a compiled list from a selected
statistcal file available on the DPP disk.
t = type: AMA, DISK
p = period: TDAY (Today), YDAY (Yesterday)
>SESSION REPORT Displays last or current polling session report.
>SESSION STATUS Displays current status of polling.
Continues on the next page.