User guide

110
Note: Even though some changes to tables MNPRIID and TRKSGRP are
allowed while LTID is mapped in table LTMAP. To help prevent possible
corruption, perform the following steps to complete PRI datafill:
1. BSY;BSY INB the D-Channel and B-Channels of the trunk.
2. Remove the associated LTID tipple from table LTMAP.
3. Make the desired table changes.
4. Add the associated LTID tipple back into table LTMAP.
5. BSY;RTS the D-Channel and B-Channels of the trunk.
SPM Trunk Provisioning Limits for pre-SP16
Note: The limits will be removed in the SP16 release, which will allow any
combination of trunk types up to the full SPM port capacity.
SPM EXECTAB lineup
The following is the basic execs datafill to allow PTS and PRI functional-
ity. Datafilled in table MNNODE.
* The PRAB500 SPM250 exec is not available until SP15. Prior to SP15,
you cannot have PRA (DMS100/200) and PRA250 (DMS250/500) PRI on
the same physical SPM. Until the PRAB500 SPM250 exec is available,
you must have the PRI trunks designated for either PRA (DMS100/200) or
PRA250 (DMS250/500) and use the PRAB SPMEX (for PRA) or the
PRAB SPM250 (for PRA250) applications. (This means in DMS500
offices the PRI trunks have to physically be in a SPM that is designated via
the execs for the DMS100 or either the DMS250 side - at least until SP15
and the PRAB500 SPM250 exec is available anyway...)
**
ABSPMX PXSPMX is not fully functional until SP16. (Even though it
can be datafilled prior to SP16.) ABSPMX PXSPMX allows PX trunks that
use FX signaling. This lineup also allows DAL and PX FX trunks to func-
tion on the same SPM.
*** AB250 PXDTCX is used for PX trunks with FX signaling pre-SP16.
Remember: DAL and PX FX cannot be placed on the same SPM prior to
SP16.
Example exec lineups in table MNNODE for DMS250/500:
Pre-SP16: (If you have standard PTS and nothing else, use: (ABTRK
SPMEX) (AB250 SPM250) (If you have standard PTS and PRI for
DMS250, use: (ABTRK SPMEX) (AB250 SPM250) (PRAB SPM250) (If
you have standard PTS and PRI for DMS100 in a DMS500 office, use:
(ABTRK SPMEX) (AB250 SPM250) (PRAB SPMEX) (If you have stan-
dard PTS, PX FX without any DAL trunks on this SPM, and PRI for
DMS250, use: (ABTRK SPMEX) (AB250 SPM250) (AB250 PXDTCX)
(PRAB SPM250) (If you have standard PTS, PX FX without any DAL
trunks on this SPM, and PRI for DMS100 in a DMS500 office, use:
(ABTRK SPMEX) (AB250 SPM250) (AB250 PXDTCX) (PRAB
SPMEX)
SP16 and above: (The following execs should handle about ANY config-
uration...but see below if placing both DAL and PX FX trunks on same
SPM...) (ABTRK SPMEX) (AB250 SPM250) (ABSPX PXSPMX)
(PRAB500 SPM250)
Example exec lineups in table MNNODE for DMS100 offices:
Pre and post SP16: (This is all you need to cover standard PTS and PRI...)
(ABTRK SPMEX) (PRAB SPMEX)
Trunk
Combination
ISUP
T1s
PTS
T1s
PRI
T1s
Notes
ISUP 84 - - Full Capacity
PTS - 56 -
Up to 56 PTS with the remaining
T1s unused
PRI 23B + D - - 84 Full Capacity
ISUP/PTS 84-59 0-25 -
Up to 25 PTS with the remaining
T1s ISUP
ISUP/PRI 84-0 - 0-84
Any combination of ISUP and
PRI to equal 84 T1s
PTS/PRI - 0-16 84-68
Up to 16 PTS with the remaining
T1s PRI
ISUP/PTS/PRI 84-32 0-20 0-32
Up to 20 PTS and up to 32 PRI
with the remaining ISUP
ISUP/PTS/PRI 84-0 0-16 0-84
Up to 16 PTS with any combina-
tion of ISUP and PRI
Appl: DMS 100: DMS 250: DMS 500:
PTS:
ABTRK SPMEX AB250 SPM250 AB250 SPM250
ABSPMX PXSPMX
**
ABTRK SPMEX
AB250 PXDTCX
***
ABSPMX PXSPMX
**
AB250 PXDTCX
***
PRI:
PRAB SPMEX PRAB SPM250
*
PRAB500 SPM250
*