Installation Guide

ManualsBrandsUniversal Hardware ManualsDoor AccessoriesHeavy-Duty All-in-One Matte Black Commercial Door Closer

ADJUSTABLE SIZE 1 THRU 6 — NON HOLD OPEN DOOR CLOSER

Closer mounts

on door, opposite hinge

side of door (push side).

(Closer cover not shown)

Closer mounts

on hinge side of door

(pull side).

(Closer cover not shown)

REGULAR ARM INSTALLATION

TOP JAMB INSTALLATION

PARALLEL ARM INSTALLATION

Closer mounts

on frame, opposite hinge

side of door (push side).

(Closer cover not shown)

See Page 5

See Page 3

See Page 4

Right hand door-RH

Left hand door-LH

Right hand door-RH

CAUTION! An incorrectly installed or improperly adjusted door closer can cause property damage or personal injury. These instructions should be

followed to avoid the possibility of misapplication or misadjustment.

DOOR CLOSER

MODEL UH4061 or UH4062 INSTALLATION INSTRUCTIONS

999-30027

PAGE 1

Summary of content (6 pages)

PAGE 1
999-30027 DOOR CLOSER MODEL UH4061 or UH4062 INSTALLATION INSTRUCTIONS ADJUSTABLE SIZE 1 THRU 6 — NON HOLD OPEN DOOR CLOSER CAUTION! An incorrectly installed or improperly adjusted door closer can cause property damage or personal injury. These instructions should be followed to avoid the possibility of misapplication or misadjustment. REGULAR ARM INSTALLATION Closer mounts on hinge side of door (pull side).
PAGE 2
COMPONENTS: 999-30027 Figure 1 Forearm Screw Forearm Adjusting Screw Backcheck Valve Latch Speed Valve Forearm Forearm Shoe Screw Pinion Dimple Sweep Speed Valve Standard Closer Forearm Shoe Mounting Plate For mounting plate installation, refer to supplemental installation sheet. Main Arm Screw Closer Arm Parallel Arm Plate Screw Package Through Bolt and Screw Plastic Cover Main Arm • It is recommended that the door be hung on ball bearing type hinges so door swings freely.
PAGE 3
999-30027 REGULAR ARM INSTALLATION MODEL UH4061 or UH4062 INSTALLATION INSTRUCTIONS 5-1/2" (140mm) 1 3/4" (44,5 mm) "A" FOOT CLof Hinge 2-3/8" (61 mm) FRAME SCREW & WASHER 1 3/8" (35 mm) DOOR 3/4" (19mm) 12" (305 mm) MODEL DIMENISON "A" INCHES 7-1/2" UH4061 UH4062 6" 4-1/2" [mm] 191 152 114 OPENING TO 100° TO 130° TO 180° DOOR WIDTH INTERIOR UP TO 60" UP TO 60" UP TO 54" EXTERIOR UP TO 48" UP TO 48" UP TO 42" CLOSER SIZE # OF TURNS OF POWER ADJUSTMENT SCREW CLOSER SIZE # OF TU
PAGE 4
999-30027 TOP JAMB INSTALLATION MODEL UH4061 or UH4062 INSTALLATION INSTRUCTIONS 12" (305 mm) "A" 3/4" (19 mm) CL of Hinge FRAME 2-3/8" (61 mm) FOOT DOOR 5/8" (16 mm) 5-1/2" (140 mm) 1-3/4" (44.
PAGE 5
999-30027 PARALLEL ARM INSTALLATION MODEL UH4061 or UH4062 INSTALLATION INSTRUCTIONS PA PLATE CL of Hinge FRAME "A" DOOR 3-1/2" (89 mm) HINGE OPPOSITE SIDE 3/4" (19 mm) 12" (305 mm) INSTALLATION SEQUENCE 1. Select degree of opening and use dimensions shown to locate 4 holes on door for closer body and 4 holes underside of frame for PA plate. FRAME 2. Prepare door and frame for fasteners (See Preparation for Fasteners, Page 2, Figure 2). 3.
PAGE 6
999-30027 CLOSER ADJUSTMENT Closing Speed Controls (Figures 1 and 2) • • Valve "1" controls sweep range Valve "2" controls latch range Figure 1 Figure 2 CLOSING SPEED - CONTROLS "1" (Sweep) "2" (Latch) Standard closing cycle Opening Door Control (Figures 3 and 4) Backcheck Valve controls the hydaulic resistance to door opening. It is not to provide a position stop.