SI M PLE ADVANCE D H O M E T H E AT E R A N D L I G H T I N G C O N T R O L I N STR UCTION MAN UAL
HOW TO SET UP LIGHTING OPERATING BEHAVIOR FOR Z-WAVE / LIGHTING FUNCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 PROGRAMMING TIME AND DAY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 CREATING A Z-WAVE NETWORK OF MODULES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PROGRAMMING TIME AND DAY HOW TO SET UP LIGHTING To set the time and date: OPERATING BEHAVIOR FOR Z-WAVE / LIGHTING FUNCTIONS button for 3 seconds without ‘MONSTER’ highlighted. (If you have not 1. Press and hold the previously used the REVOLUTION Remote Control Setup Wizard, the on-remote screen will display the message, “Use Web Setup or Press OK to Use Remote Setup”). key shift It’s highly recommended you read the Glossary of Terms and this section before reading any other lighting-related section.
CREATING A Z-WAVE NETWORK OF MODULES A network is the sum total of Z-Wave modules you have paired with your REVOLUTION remote where each module is referred to as a “node.” You can add and delete nodes from your network. You can also rename nodes as you see fit. While there are a variety of commands your remote can perform on the network of nodes as a whole (and they are detailed in later sections), for now, let’s focus on adding, deleting and renaming individual nodes.
Customizing the ALL ON/OFF Feature Unless you customize the behavior of the ALL ON/OFF feature, then by default, the remote will attempt to turn on or off, all modules it finds on your Z-Wave network based on the current state of toggle. 6. The LCD screen displays, “Include in All ON/OFF” and awaits a signal from the module you wish to include. Hold the remote near the module and press the pairing button on the module.
or 5. The menu changes and Setup is highlighted. Use the instead. Press the button and the remote lists all scenes. MANAGING SCENES Scenes are collections of nodes you specify as related to one another in a way that’s meaningful to you. For example, you keep several paired lighting modules in a certain room of your home. To control all of them in a preset way, you can create a scene, include them in the scene, and control them using a button. scene The remote stores up to 18 scenes.
5. The menu changes and Setup is highlighted. Use the or button to highlight Delete Scene instead (a fourth menu choice not displayed among the first three). Press the button. 6. The screen displays, “Press the desired scene button.” Press the scene button for the scene you wish to delete. How to Delete / Remove a Scene Controller from your Z Wave Network To delete a scene controller from the memory of your remote: 1.
scene you chose in the previous step, press the OK button and hold the remote 3” to 5” from the scene controller. 8. The remote displays the message, “Sending” shortly followed by either “Fail” or “Success” displayed for 3 seconds. 9. The menu returns to step #4 with Scene Controller highlighted by default. How to Remove a Scene from a Button on the Scene Controller 4. Use the or button to highlight Update Control. 5.
or Use the buttons to change the hours to your preferred time. Once you have it set, use or button to highlight the minutes and proceed in the same way until each element of the On Time is set the way you want it. Once you’ve done this, press the button to save your preferred On time for this event. 10. Next, the screen reads, Off Time followed by the default time. Follow the same procedure as step #10 to set the time this event will turn off.
Preparing the Destination Controller to Receive Data Copy Option 2: Create Secondary Controller – Network Only First, it is necessary to place the destination controller into a receiving state. If your destination controller is also a REVOLUTION Remote Control, follow the steps below. 1. On your source remote, follow the same steps 1 to 4 you just performed on your Destination controller (see Preparing the Destination Controller to Receive Data). On your destination controller: 2.
If the copy succeeds, the source remote screen will say SUCCESS. Otherwise, it will read FAIL or EMPTY (to specify the network has zero nodes). MANAGING NETWORK SETUP At the network level, there are four operations the remote can perform: Network Reset, Network Recovery, Network Update, and Remove Fail Node. Network Update Network Reset Network Update ____ all nodes on the network.
Controlling Thermostats GLOSSARY OF TERMS Your REVOLUTION remote can control any Z-Wave enabled thermostat. To find the pairing button for your Z-Wave enabled thermostat, consult your manufacturer’s manual. Z-Wave: Z-Wave uses reliable, low power radio waves to control all aspects of your home wirelessly: lighting, climate control, safety and security, home entertainment, energy conservation, remote monitoring, and more.
www.MonsterCentral.com ©2010 Monster, LLC 7251 West Lake Mead Blvd. Las Vegas, NV 89128 Monster, the Monster logo, Revolution 200, Monster Central, and the Monster Central logo are trademarks or registered trademarks of Monster Cable Products, Inc. or its subsidiaries in the United States or other countries. Blu-ray Disc is a trademark of Sony Kabushiki Kaisha Corp.
