45608 Home Theater Remote with Z-Wave® Lighting Control SmartHome ™ Manage your home entertainment system and lighting with one remote! Controls 12 Audio/Video Devices and up to 232 Z-Wave Devices www.easyzwave.
Table of Contents Introduction Audio/Video Key Chart. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Batteries. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Automatic Time-Out. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Set-Up, Initial A/V Setup. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Audio/Video Key Chart A. SET – Press & hold to enter setup mode. When in setup mode, press & release to back up one level in the setup menu or press & hold to cancel setup. I A J B. ARROWS – Scroll left or right to highlight desired menu item. Highlighted menu item in center of display is active. C. OK – Press & release to select highlighted menu item D. NUMBER KEYS – Dependent upon Audio Video device being controlled. Examples: TV - channel selection; Receiver – input selection C B E.
Batteries Four “AAA” Alkaline batteries (not included) are required. Battery Use and Safety • Use only fresh batteries of the required size and recommended type. • Do not mix old and new batteries or different types of batteries. • If you do not plan to use the remote for an extended period, remove the batteries. They can leak chemicals that can destroy electronic parts. • Dispose of old batteries promptly and properly. Do not burn or bury them. To Install Batteries 1.
NOTE: If an invalid code is entered, the LED emits one long blink, and the LCD displays INVALID. 5. The selected device turns off if the code was successful. You can also try pressing additional keys on the remote to test other functions. 6. If the code you entered functions properly for all keys tested, Press OK to save the code. 7. If the code you entered does not function properly, Press SET one time and repeat steps 2-6, trying the next available code from the manufacturer’s code list. 8.
4. Use the ARROW keys to view codes of other devices you have set up. 5. After viewing the codes, press OK or SET to exit. Replacing a Device This replaces an existing device with a new device in your remote’s programming. One example could be replacing your cable box with a satellite receiver. NOTE: The new device replaces and overwrites all settings of the current device (Key Mover, Learning, and all other userprogrammed features). The one exception is with macros.
4. The remote displays LOCK VOLUME. Press OK. 5. The remote displays USE < > TO SELECT VOLUME SOURCE THEN PRESS OK. 6. Use the ARROW keys to select the device to be locked. The remote displays the name of the device and its code (for example, LOCK VOLUME TO RECEIVER 1158). 7. Press OK. The display changes to VOLUME CONTROL IS NOW SET TO RECEIVER 8. The display automatically changes to LOCK VOLUME after a few seconds. Press SET to exit. Adding a Device to Volume Lock 1.
5. The remote displays DELETING ALL PUSH OK TO CONFIRM. Press OK. 6. The remote displays ALL MOVED KEYS DELETED PUSH OK TO DELETE MORE. Press OK to delete keys for a different device or SET to exit. Deleting a Single Copied Key 1. From the ADD KEY MOVER screen, scroll to DELETE KEY MOVER. Press OK. 2. The remote displays FIND MODE PUSH OK. On the bottom line, the device name is displayed (for example, TV). 3. Scroll to the device you wish to delete the copied keys from. Press OK. 4.
3. The remote displays SELECT MACRO KEY TO DELETE AND PUSH OK. 4. Once you have pressed a valid macro key, the remote displays MACRO DELETED CHOOSE ANOTHER OR OK TO EXIT. 5. Repeat steps 2–4 above until you have finished deleting key macros. Press SET when finished to return to normal operation. Learning Your remote can learn functions from other IR remote controls if you cannot find your device code. NOTE: Learning can not be done in Z-Wave mode.
Deleting a Single Learned Key To delete a single learned key, follow steps 1–3 above. Then perform the following steps: 1. Press the key containing the learned function to be deleted. The remote displays KEY DELETED PUSH OK TO DELETE ANOTHER. 2. Press SET to exit or OK to delete another learned key LCD Timer Setting the LCD Display’s Contrast 1. From ADVANCED FUNCTIONS, scroll to CONTRAST. Press OK. 2. The LCD displays CONTRAST SETUP, with 10 blocks to show the CONTRAST setting.
Z-Wave Overview Z-Wave Terminology Please note: The terms “Device”, “Node” and “Light” all refer to an individual Z-Wave enabled device in your home control network and are interchangeable within the context of these instructions. If this remote is used as the primary controller, you must use it to create your control network. You can use multiple remote controls with your Z-Wave lighting control network; however, only one remote will act as the primary controller.
Wireless Range This device complies with the Z-Wave standard of open-air, line of sight transmission distances of 65 feet. Actual performance in a home depends on the number of walls between the remote controller and the destination device, the type of construction and the number of Z-Wave enabled devices installed in the control network. Every Z-Wave enabled device acts as a signal repeater and multiple devices result in more possible transmission routes which help eliminate “RF dead-spots”.
Z-Wave Key Chart K A A. SET – Press & hold to enter setup mode. When in setup mode, press & release to back up one level in the setup menu or press & hold to cancel setup. B B. SHIFT – For use in Z-Wave setup & operation modes. Press & release to shift number key from devices 1 – 9 to 10 – 18. C. ARROWS – scroll left or right to highlight desired menu item. D. OK – Press & release to select highlighted menu item D C E.
Z-Wave Setup 2. Add devices to your home network (maximum of 232) without assigning them to a specific number key. These devices can only be controlled through the GROUP, SCENE or ALL commands. With the remote in Z-Wave mode, press & hold the SET Key for the following menu options: Add a device without assigning it to a specific number key 1.
Turning a Light On or Off • To turn a light on, press and release the CH + key for less than one second. The screen will display ON above the selected Light/Node. • To turn a light off, press and release the CH - key for less than one second. The screen will display OFF above the selected Light/Node. Setting a Light’s Brightness Level • To brighten a light, press and hold the VOL + key for more than one second. The screen will display BRIGHT UP above the selected Light/Node.
• To turn a GROUP off, press and release the CH - key for less than one second. The screen will display OFF above the selected GROUP. Removing a Device (Node / Light) From a Group: This only removes the device from a specific group. The device is still part of your home control network and the group still exists (if there were more than one device in it to start). 1. Enter Z-Wave setup mode and highlight GROUP SETUP 2. Press OK; the screen will display ADD 3.
• To turn a SCENE off, press and release the CH - key for less than one second. The screen will display OFF above the selected SCENE. Removing a Device (Node / Light) From a Scene This only removes the device from a specific scene. The device is still part of your home control network and the scene still exists (if there is more than one device in the scene). 1. Enter Z-Wave setup mode and highlight SCENE SETUP 2. Press OK; the screen will display ADD 3.
Adding or Excluding a Device To / From All Control Menu options under ALL SETUP include EXCLUDE ALL ON OFF, INCLUDE ALL ON OFF, EXCLUDE ALL ON ONLY and EXCLUDE ALL OFF ONLY. 1. Enter Z-Wave setup mode and highlight ALL SETUP. 2. Press OK; the screen will display EXCLUDE ALL/ON OFF 3. Use the ARROW keys to scroll to the desired action. 4.
14.To set the OFF TIME of your event; d. Use the right or left ARROW keys to scroll right or left. e. Press the CH + key to move hour, minute, AM or PM forwards. a. Press the CH - key to move the hour, minute, AM or PM backwards. 15.When you’ve set the OFF TIME, press OK; the screen will display SUCCESSFUL indicating you successfully programmed your event. Enabling or Disabling an Individual Event: 1. Enter Z-Wave setup mode and highlight EVENTS. 2. Press OK; the screen will display ADD. 3.
To Change Advanced Configuration Settings: 1. Enter Z-Wave setup mode and highlight THERMOSTAT 2. Use either ARROW key to scroll until the display reads ADV CONFIG 3. Press OK and screen will display PARAMETER 0 4. Use either ARROW key to scroll until the display reads the proper parameter number (1 - 255) as indicated in the Z-Wave device’s instructions 5. Press OK and the screen will read NUMBER OF BYTES 6.
The Primary remote then transmits the network and device information to the new Secondary remote. 7. Both remotes should indicate a successful completion of the copying process. a. The 45608’s screen will display SUCCESSFUL. b. Other GE models or other brands will indicate success in various ways, depending on the remote’s capabilities. Please refer to its instructions for details. 8. Change individual devices, groups, scenes, etc. on the new secondary remote as needed.
Network Update Network Reset Recovery Update Remove All Failed Nodes Resetting Your Network You can reset your network to clear all device and Z-Wave network information from the remote. This does not reset the Z-Wave devices to their factory default. Each device still needs to be deleted in order to reset them. Please refer to the section on “Deleting a Device (Node/Light) from Your Network” for details. To reset your network: 1. Enter Z-Wave setup mode and scroll to NETWORK 2.
WARRANTY JASCO Products warrants this product to be free from manufacturing defects for a period of two years from the original date of consumer purchase. This warranty is limited to the repair or replacement of this product only and does not extend to consequential or incidental damage to other products that may be used with this product. This warranty is in lieu of all other warranties, expressed or implied.
For Audio - CD DKK. . . . . . . . . . . . . . . . . . . . . . . . . . 0000 Fisher. . . . . . . . . . . . . . . . . . . . . . . . 0000 Harman/Kardon. . . . . . . . . . . . . . 0100 Inkel. . . . . . . . . . . . . . . . . . . . . . . . . . 0180 Integra. . . . . . . . . . . . . . . . . . . . . . . 0101 JVC. . . . . . . . . . . . . . . . . . . . . . . . . . . 0072 Kenwood. . . . . . . . . . . . .
For Audio - Receiver, cont. Pioneer. . . . . . . . . . 1023, 0014, 0150, . . . . . . . . . . . . . . . . . . . 0531, 0630, 1384 Polk Audio. . . . . . . . . . . . . . . . . . . . 1289 Proscan . . . . . . . . . . . . . . . . . . . . . . 1254 RadioShack. . . . . . . . . . . . . . . . . . . 1609 RCA . . . . . . . 1023, 1609, 1254, 0531, . . . . . . . . . . . . . . . . . . . 1074, 1390, 1511 Realistic. . . . . . . . . . . . . . . .
For Television, cont. Jensen . . . . . . . . . . . . . . . . . . . . . . . 0761 JIL. . . . . . . . . . . . . . . . . . . . . . . . . . . . 0030 Jutan. . . . . . . . . . . . . . . . . . . . . . . . . 0030 JVC. . . . . . . . 0054, 0053, 0030, 0650, . . . . . . . . . . . . . . . . . . . . . . . . . 0731, 1253 Kamp. . . . . . . . . . . . . . . . . . . 0017, 0180 Kawasho. . . . . . . . . . . . . . . . . .
For Video - VCR, cont. Citizen. . . . . . . . . . . . . . . . . . 0035, 0000 Colortyme. . . . . . . . 0060, 0035, 0045 Colt. . . . . . . . . . . . . . . . . . . . . . . . . . . 0000 Criterion. . . . . . . . . . . . . . . . . . . . . . 0000 Crosley. . . . . . . . . . . 0035, 0081, 0000 Curtis Mathes. . . . . 0060, 0035, 0000 CyberPower . . . . . . . . . . . . . . . . . . 1972 Daewoo. . . . . . . . . . . .
For Video - DVD, cont. Kloss. . . . . . . . . . . . . . . . . . . . . . . . . 0533 Lasonic. . . . . . . . . . . . . . . . . . . . . . . 0627 Lecson . . . . . . . . . . . . . . . . . . . . . . . 1533 LG. . . . . . . . . . . . . . . . . . . . . . . . . . . . 0591 Magnasonic. . . . . . . . . . . . . . . . . . 0675 Magnavox. 0503, 0539, 0646, 0675 Marantz. . . . . . . . . .
