User Manual
Table Of Contents
- UAD Powered Plug-Ins
- Introduction
- UAD Installation
- Overview
- QuickStart DVD
- System Requirements
- Supported Hosts
- Latest Information & Software Updates
- UAD Software Installation
- Install Software First
- UAD Hardware Installation
- Authorization
- Authorize Plug-Ins Procedure
- Load Authorization File
- Offline Authorization
- Using Unlicensed Plug-Ins
- Verifying Installation
- Learn More
- Software Removal
- UAD System Overview
- My.uaudio.com
- Using Multiple UAD Cards
- UAD Meter & Control Panel
- Overview
- Launching the UAD Meter & Control Panel Application
- Using the UAD Meter
- UAD Meter Elements
- UAD Control Panel
- System Information Panel
- Plug-Ins Panel
- Configuration Panel
- Help & Support Panel
- Using UAD Powered Plug-Ins
- Tempo Sync
- UAD Delay Compensation
- UAD-Xpander & UAD-Xtenda
- LA-2A and 1176LN
- LA-3A Compressor
- Fairchild 670
- Precision Multiband
- Precision Limiter
- Precision Buss Compressor
- Neve 33609 Compressor
- VCA VU
- Neve 88RS Channel Strip
- CS-1 Channel Strip
- Precision Equalizer
- Cambridge EQ
- Pultec and Pultec-Pro
- Neve 1073 Equalizer
- Neve 1081 Equalizer
- Helios Type 69 Equalizer
- Roland CE-1
- Roland Dimension D
- Roland RE-201
- RealVerb Pro
- DreamVerb
- Plate 140
- Precision Maximizer
- Precision De-Esser
- Precision Enhancer kHz
- SPL Transient Designer
- Nigel
- Introducing Nigel
- Preflex Plug-in
- Preflex Modules
- Gate/Comp Module
- Amp Module
- Amp Controls
- Cabinet Module
- Phasor Module
- Mod Filter Module
- TremModEcho plug-in
- Trem/Fade Module
- Mod Delay Module
- Echo Module
- Moog Multimode Filter
- History
- Index

UAD Powered Plug-Ins Manual - 60 - Chapter 6: UAD Meter & Control Panel
UAD-2
The displayed latency is the audio I/O interface buffer size when Extra Buff-
ering (page 67) is off. When Extra Buffering is on, the displayed latency is the
audio I/O interface buffer size plus 64 samples.
UAD-1
The displayed latency is twice the audio I/O interface buffer size.
Note: The displayed sample latency number does not include the extra sam-
ples produced by upsampled UAD plug-ins. For more detailed information
about the extra samples and latency, see “Compensating Upsampled
Plug-Ins” on page 95.
Hardware
Section
Detailed information about each UAD card and its DSP is displayed in the
Hardware area (Figure 10 on page 59). If you have several cards installed,
use the scrollbar to see the other cards.
Card Status For each installed card type (UAD-2 and UAD-1), a small picture of the hard-
ware and its status is displayed. When the card displays Status: OK the hard-
ware is operating properly. The total number of UAD plug-ins loaded on each
card is also displayed here.
Card Enabled Individual UAD cards can be disabled using the Card Enabled button.
This can be useful, for example, if creating a session on a system with
multiple cards that will be transferred to a system with fewer cards, to
streamline the performance of the host system when multiple cards are not
needed, or to manually balance loads on UAD-1-only multicard systems.
Click the button to disable an individual card. The card is enabled
when the button is blue. For additional information regarding multi-
card use, see Chapter 5, “Using Multiple UAD Cards.”
Cards remain disabled only while the UAD Meter & Control Panel application
is open. When the UAD Meter & Control Panel is quit, disabled cards are
re-enabled.
Note: Disabling cards does not disable plug-ins already running on the card;
it only prevents additional plug-ins from being loaded onto it.
Important: For optimum results, quit any host applications using UAD
plug-ins before disabling/enabling cards.