User's Manual

ADVANCE
- EN
Page 2,3 [Connection Method]
■ A. Cautions on Connecting Motor
To increase rotation force, when connecting the motor capsule to the speed reduction capsule or worm gear capsule,
be sure to make black gears engaged with each other, or the motor and gear will not work correctly.
a-1. Black Connectors a-2. Motor Capsule a-3. Speed Reduction Capsule a-4. Worm Gear Capsule
■ B. How to Connect the Crown Gear Capsule
b-[1]. (top view) The left wheel and the right wheel rotate in the same direction. Engage the small gear to the speed reduction
capsule for forward and backward movements.
b-[2]. (side view)The left wheel and the right wheel rotate in the diuerent direction. The left wheel and the right wheel rotate in the
diuerent direction for rotation. Engage the big gear to the speed reduction for spinning.
b-1. Motor Capsule b-2. Speed Reduction Capsule b-3. Crown Gear Capsule
■ C. Connector Opener
When it's diflcult to remove the octagonal connector or tire from the capsule or wheel, please use the connector opener like the
picture C. Then you can remove them with ease.
■ D. Connecting Cells in series and parallel
d-1. a series connection d-2. a parallel connection
It can be 6 voltage if you connect batteries in series such as ‘1’ and it is 3 voltage if you connect batteries in parallel such as ‘2’.
(Connecting cells in series make high voltage but the battery has a short life. And the battery has a long life
if it’s connected in parallel, but the electric power is not strong than connecting in series.)
■ E. Connecting method of the Receiver Capsule
Connect 6 voltage of batteries to the IN terminal of the Receiver Capsule and the Motor Capsule to the OUT terminal of
the Receiver Capsule.
Tip.1 Please make sure IN terminal for battery is Black connector.
Tip.2 Please make sure OUT terminal for motor is Blue, Green and Red connector.
■ F. Manual paring
f-1. After connect the batteries to the Receiver Capsule, please push the paring button inside of the Receiver Capsule by using the
Connector Opener. Then the Red light on the Receiver Capsule blinks.
f-2. Pull down the Blue lever on the Remote Controller and hold it around 30 seconds, then the Red light on the Remote Controller
blinks. If the Red light on the Receiver Capsule blinks while pulling down the Blue lever, the paring is done.
■ G. Function of Remote Controller
g-1. Green light; it’s turned on when the Remote Controller is working.
g-2. Red light; it’s turned on when the paring is on progress.
g-3,4,5. Lever; connected motor on each color of the connector can be controlled by pulling down or up the same color of lever.
Page 4 [Parts Number, Parts Name]
1. Motor Capsule
2. Speed Reduction Capsule
3. Worm Gear Capsule
4. Crown Gear Capsule
5. Internal Gear Capsule
6. Transmission Capsule
7. Axle Capsule(S)
8. Axle Capsule(L)
9. IQ Capsule (S)
10. Q Capsule (L)
11. Free Coupler
Standard Capsule
12. Connector
13. Battery Case (L)
14. Lead Line
15. Lead Line (2 in 1)
16. Coupler
17. Cap Nut
18. Wheel (S)
19. Wheel (L)
20. Tire (S)
21. Tire (L)
22. Gear Wheel
23. Chain
24. Cable tire
25. Winding Drum
26. Hook
27. Cable
28. Impelle
29. Floater
30. Cap
31. Bar Connector
32. Straight Bar Connector (S)
33. Straight Bar Connector (L)
34. Diagonal Bar Connector (S)
35. Diagonal Bar Connector (L)
36. Cube Block
37. Connecting Pin(A)
38. Connecting Pin(B)
39. Angle Pin (A)
40. Receiver Capsule
41. Remote Control
42. Connector Opener
1. Motor Capsule : Receiving power from batteries, the motor capsule creates rotating force. According to the polarity of power,
the motor capsule can rotate in both ways.
2. Speed Reduction Capsule : The speed reduction capsule slows rotation speed but increases rotation force. Be sure to engage
the motor capsule's black gear (output) with the speed reduction capsule's black gear (in put) for correct operation.
3. Worm Gear Capsule : Functions of the speed reduction capsule and crown gear capsule are conmbined into one part
worm gear capsule. The black gear delivers the rotation speed to the opposite side while the other gear decreases
the rotation speed and converts the rotation direction to 90 degrees. Be sure to engage the motor capsule's
black gear (output) with the speed gear capsule's black gear (input) for correct operation.
4. Crown Gear Capsule : The crown gear capsule converts received rotation force into a forward or 90 degrees direction.
According to chain connection, the gears rotate in the same direction or opposite directions.
5. Internal Gear Capsule : The internal gear capsule increases or decreases rotation speed in a forward direction.
When a big gear is engaged, the rotation speed is up, and when a small gear is engaged, the rotation speed is down.
6. Transmission Capsule : With the transmission capsule, all kinds of gear capsules can be extended and rotation force is delivered
between gears without variation.