System information

ManualsBrandsUnitech ManualsCell PhonePA960

Introduction

unitech PA960

First Steps with the Unitech PA960

NOTE: data you enter may not be properly stored until

the built-in backup battery has been adequately charged.

Please be remided to turn on the back up battery before

you charge the terminal

Tour of the unitech PA960

PA960 Front and Left Side

PA960 Back

Additional accessories are shipped separately.

unitech PA960& Accessories

After opening the box, please make sure the

following accessories for the PA960 are present:

Pulling-tags RF Card Cushion

PA960 Main Body

PA960 Windows CE.NET4.2

Quick Reference Guide

Power system

Power Status Indication

Unpack the box and save the packaging in the

event the unit needs to be stored or returned to

unitech for service.

Check the unit for shipping damage. If anything

is missing or damaged, notify your unitech sales

representative.

There are three ways to provide power to the PA960:

PA960 CD

Installing the Wireless Local Area

Network (WLAN) Card

400355 Rev. A

Your PA960 is a rugged, compact and lightweight

palm-size computer. It utilizes the Windows CE®

operating system, and incorporates an integral bar

code scanning laser device, color LCD with touch

screen, keypad, IrDA interface, and wireless

communication capability. It provides the user with

a standard Windows-based environment for

customizing and operating the device.

This PA960 product reference guide will guide you

to access your PA960.

Docking Station

RS232/Charging cable,USB/Charging cable

Rechargeable Lithium-Ion battery pack

Charging the Lithium-Ion Battery

Pack

The optional Docking Station is a convenient accessory for

daily use of the PA960. The charging will be completed

withing 3 hours. Or, when using the included Charging/RS232

Cable or Carging / USB cable the charging time of the battery

pack is about 3 hours.

Charging the Main and Backup Battery for the First Time

Operating the PA960 for the first time without the AC

adapter, and without fully charging the backup battery

may result in loss of data stored in RAM memory.

Note: Backing-up data by backup battery only without the

main battery installed in the battery compartment may take as

long as 8 hours. Therefore, in order to prevent data protection

failure due to backup battery failure, do not leave the PA960

without the rechargeable battery pack installed, or without

connection to AC power for an extended period of time.

It may take up to 72 hours to backup data when the PA960 is

automatically shut down because of very low battery power

while the depleted batteries are still installed in the battery

compartment.

Battery Very Low

Plug with power adapter

Battery Low

Four different icons are displayed on the status bar to indicate

the on-board power status.

“Plug” icon: When displayed, this icon indicates that the battery

is charging. The PA960 is either plugged-in via the DC 12V/2A

power adapter or in the

docking station.

“Battery Low” icon: When displayed indicates the

battery is low and needs to be charged. In other words,

there is no external power supply, the battery charge is low or

very low, and charging the

PA960 is recommended.

“Battery Very Low” icon: When displayed indicates the battery

is very low. Stopping the operation and charging the PA960

immediately is highly

recommended.

Bac

ttery

Backup Battery Very Low or

Backup Battery is not turned on.

No icon: When displayed means there is no external power

supply to the PA960 but its

battery power status is good.

“Backup Battery Low” icon: When displayed indicates the

backup battery is low and

needs to be charged.

“Backup Battery Very Low” icon: When displayed indicates

the backup battery is very low. Stopping the operation and

charging the PA960

immediately is highly

recommended.

Troubleshooting

If the screen is blank or the unit fails to turn on, charge the

battery for 16 hours. If the battery is fully charged and the unit

still fails to turn on, reboot the device by inserting a pin in the

reset hole.

PCMCIA

card front side

Insert the RF card into the PCMCIA slot.

Attach pulling-tag to antenna.

Attach the snap-on antenna to the RF card if required (only

the Cisco card comes with a pre-installed antenna).

Remove the stylus, using the screw driver in

the stylus to remove the screw, and then

open the PCMCIA compartment

Power off the PA960

Laser

FCC Statement

The Unitech PA960 is certified in the U.S. to conform to the

requirements of DHHS/CDRH 21CFR Subchapter J and to the

requirements of IEC 825-1. Class II and Class 2 products are

not considered to be hazardous. The PT930 contains

internally a Visible Laser Diode (VLD) whose emissions do not

exceed the maximum limits as set forth in the above

regulations. The scanner is designed so that there is no

human access to harmful laser light during normal operation,

user maintenance or during prescribed service operations.

CAUTION - Use of controls or adjustments or performance of

procedures other than those specified herein may result in

hazardous laser light. Use of optical instruments with the

scanner will increase eye hazard. Optical instruments include

binolulars, microscopes, and magnifying glasses. This does

not include eye glasses worn by the user.

The laser safety warning label required by the DHHS/IEC for

the PT930’s optional laser scanner module is located on the

memory compartment cover, on the back of the unit.

This is a FCC Part 15 Class B product. In a domestic

environment this product may cause radio interference,

in which case the user may be required to take adequate

measures.

www.unitech-adc.com

Battery pack

Stylus

This stylus is design for tapping

screen and also for accessing

batter door via the screw driver

in the stylus.

Bar Code Laser Scanner

Right Side Scanner

Trigger

Press it to enable

laser sccanner to

read bar code.

Keypad

Touch Screen

RS232/USB/Charging Port

IrDA port

Reset Hole

Push enclosed

button for system

warm-start

CF slot compartment

Please remove the

battery door to access

CF slot.

Battery compartment

Install Lithium-ion battery

pack here.

PCMCIA compartment

Install PC card here.

Note: Before using the PA960 for the first time, charge

the unit for 16 hours to fully charge the empty backup battery.

Check Battery Status:

The battery menu item will show the status

of the main and backup batteries. There

are 3 kinds of status indicators — “Good”,

“Low” and “Very Low”. Bold characters

indicate the actual status, e.g. battery icons

in the illustration at right mean both the main

and backup batteries are “GOOD”.

It is necessary to charge the battery when “Low” or “Very Low”

are displayed in bold characters. If “Low” or “Very Low” are

still displayed after charging, please contact Unitech

Technical Support.

PA960 Windows CE.NET 4.2

Quick Reference Guide

Laser Scanner

The PA960 has an integrated laser scanner, which

reads all major bar code labels with excellent performance.

Trigger keys are located on the left and right sides of the unit.

Press either one to activate the laser scanner.

The PA960 also has a built-in Scanner Setting.exe program

that allows the user to test the barcode scan function.

Scanner Setting.exe is located in directory \Windows\Control

and is also accessible by shortcut via “Setting\Control” on the

Start menu.

European Conformity Statement

Declaration of Conformity with Regard to the R&TTE

1999/5/EC and EMC 89/336/EEC directives.

CF slot drawer for PA960

Summary of content (2 pages)

PAGE 1
Laser Scanner 12 The PA960 has an integrated laser scanner, which reads all major bar code labels with excellent performance. Trigger keys are located on the left and right sides of the unit. Press either one to activate the laser scanner. The PA960 also has a built-in Scanner Setting.exe program that allows the user to test the barcode scan function. Scanner Setting.exe is located in directory \Windows\Control and is also accessible by shortcut via “Setting\Control” on the Start menu.
PAGE 2
Setting up the PA960 4 Your Unitech PA960 is shipped with a protective film over the display. This film may be left in place to protect the screen from scratches, however, it will slightly reduce the readability and contrast of the image. You may remove the protective film by peeling it off from one corner. 5 Supplying power to the PA960 Connect the RS232/Charging Cable or USB/Charging Cable to the PA960, and then connect the AC adapter to the cable’s power jack and an electrical outlet.