because we care MS912 Wireless Barcode Scanner Quick Guide Full user’s manual is available on the enclosed CD. Version 1.
FCC WARNING STATEMENT This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
OUT OF THE BOX INTRODUCTION 2. Trigger because we care 3. LED Indicator Mini Wireless Barcode Reader NUMERIC BARCODES MS912 Wireless Barcode Reader *1* *2* *3* *4* *5* Quick Guide Quick Guide 1. Mini USB port (for charging only) CD 1 2 3 4 5 Quick Connection Card USB Charger Cable Hand Strap -3- SPECIFICATIONS Light source Scan rate Sensor Resolution PCS Housing Profile Working Hours Charge Time Coverage 4. Exit Window 5.
GETTING STARTED BEEPER INDICATION Single long beep Single beep Single short beep Two beeps Two short beeps To scan a barcode, make sure the aiming beam crosses every bar and space of the barcode. High-low beeps Low-High beeps Five beeps Three beeps Three short beeps CHARGING THE BATTERY Several short beeps LED INDICATION 1. Flip open the mini USB port on the scanner. 2. Insert the mini USB connector into the port on the scanner and USB A connector into a USB port on the host PC.
GETTING CONNECTED PINCODE SETUP There are two modes of wireless communication: . E043$ *.E043$* (Recommanded) BT mode - HID 1. Press the trigger for 1 second to activate the scanner. 2. Scan [DISCONNECT] 3. Scan [BT mode - HID]; the scanner will emit several beeps. 4. Select “Wireless Scanner” from discovered device list. 5. The Bluetooth application may prompt you to scan a pincode(see PINCODE SETUP section) it generated. 6. The scanner will beep twice to verify the connection. .
NUMERIC BARCODES *1* *2* *3* *4* *5* -9- 1 6 2 7 3 8 4 9 5 0 *6* *7* *8* *9* *0* - 10 -
SMARTPHONE CONNECTION - iOS (Apple) Getting Connected Please pair with the scanner via [BT mode - HID]. (page 7) Getting Connected without Pincode . E049$ ENABLE SSP Secure Simple Pairing (SSP), supported by Bluetooth 2.1 or above, allows you to pair with iOS without pincode. Please scan [Enable SSP] above before entering the pairing procedure of [BT mode - HID]. (page 7) Touch Keyboard . E047$ ENABLE iOS HOTKEY . E048$ DISABLE iOS HOTKEY 1.
GENERAL SETTINGS POWER OFF TIMEOUT The timeout before automatic power-off to save power. . B017$ *.B017$* *.B018$* *.B019$* *.B020$* *.B021$* 1 MIN . A001$ DEFAULT . P023$ . B018$ 3 MIN RESET . A007$ . B019$ 5 MIN CHECK VERSION BEEPER . B020$ . F012$ 10 MIN BEEP OFF . B021$ - 13 - .
READING MODE TERMINATOR . F002$ . D012$ TRIGGER CR . D011$ . F003$ TOGGLE LF . D013$ . F001$ FLASH CR + LF . D010$ . F005$ CONTINUOUS NONE . D015$ . F006$ CONTINUOUS AUTO OFF SPACE .
KEYBOARD LAYOUT . C010$ ENGLISH (USA) JAPAN (106 key) ENGLISH (UK) CANADIAN (FRENCH) FRENCH CANADIAN (TRADITIONAL) . C018$ . C009$ . C025$ . C034$ . C012$ . C029$ . C011$ GERMAN NORWEGIAN . C026$ . C014$ ITALIAN SWEDISH . C031$ .
KEYBOARD LAYOUT . C017$ CZECH (QWERTY) BELGIAN (AZERTY) . C030$ . C028$ . C022$ CZECH (QWERTZ) DUTCH . C027$ . C021$ HUNGARIAN (QWERTZ) DANISH . C032$ . C024$ HUNGARIAN (101 KEY) SLOVAK . C033$ . C016$ SWISS (GERMAN) . C023$ SWISS (FRENCH) - 19 - BRAZILIAN (PORTUGUESE) .
ENABLE SYMBOLOGIES . G010$ . A002$ ENABLE ALL CODE CODE 93 . N017$ . K010$ CODE 32 IATA . L014$ . L010$ UK PLESSEY TELEPEN . L001$ . N032$ MSI GS1 DATABAR INDUSTRIAL 2 OF 5 GS1 DATABAR LIMITED MATRIX 2 OF 5 GS1 DATABAR EXPANDED . N010$ . N001$ . M010$ - 21 - .
BATCH MODE MEMORY MODE For memory version only . R001$ Being out of range, the scanner will temporarily keep scanned data in its memory buffer(2K RAM) until the buffer is full. The scanner will send all stored data back to the host after getting in range. ENABLE MEMORY *Note: Batch Mode will not function when Memory Mode is enabled, or no connection is made beforehand. DISABLE MEMORY *.R001$* *.R002$* .
OUTPUT DATA For memory version only DATA FORMAT . R003$ *.R003$* OUTPUT DATA You may output data ONLY when memory is enabled (page 24). Data Output Method . R014$ *.R014$* *.R013$* WIRELESS . R013$ USB-VCP To output stored data via Wireless, please do the following: 1. Scan [WIRELESS] 2. Scan [OUTPUT DATA] To output stored data via USB-VCP, please do the following: 1. Install VCP driver (available on CD) 2. Connect the scanner & host with USB cable 3. Scan [USB-VCP] 4. Save data as *.
DATE FORMAT For memory version only TIME FORMAT . R008$ *.R008$* For memory version only . R009$ DATE FORMAT TIME FORMAT *.
DATE & TIME SETUP For memory version only . R006$ *.R006$* SET DATE Example: To set Date to 2012-08-01 (Year-Month-Day): 1. Scan [Set Date] 2. Scan [1], [2], [0], [8], [0], [1] on page 9 & 10. 3. Scan [Set Date] TEST BARCODES Code 39 CODE-39 TEST Interleaved 2 of 5 . R007$ *.R007$* SET TIME Example: To set Time to 08:10:30 am (Hr:Min:Sec) 1. Scan [Set Time] 2. Scan [0], [8], [1], [0], [3], [0] on page 9 & 10. 3.
