Bluetooth Barcode Scanner - MS852B - User's Manual Version 1.
Change Log Date Change Description Version
MS852B User’s Manual Preface About This Manual Thank you for purchasing the unitech product. This manual explains how to install, operate and maintain our product. No part of this publication may be reproduced or used in any form, or by any electrical or mechanical means, such as photocopying, recording, or information storage and retrieval systems, without permission in writing from the manufacturer. The material in this manual is subject to change without notice.
MS852B User’s Manual 1. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. 2. This device complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. To maintain compliance with FCC RF exposure requirements, avoid direct contact to the transmitting antenna during transmitting.
MS852B User’s Manual European Conformity Statement unitech Electronics co., Ltd herewith declares that the unitech product is in compliance with the essential requirements and all other provisions of the RED 2014/53/EU directive, the EMC 2014/30/EU directive and the Low Voltage 2014/35/EU directive. The declaration of conformity is available for download at : https://portal.unitech.
MS852B User’s Manual Waste electrical and electronic equipment (WEEE) unitech has set up a policy and process to meet the EU directive 2002/96/EC and update 2003/108/EC concerning electronic waste disposal. For more detailed information of the electronic waste disposal of the products you have purchased from unitech directly or via unitech’s resellers, you shall either contact your local supplier or visit us at : https://portal.unitech.eu/public/WEEE iv © 2019 unitech Electronics Co., Ltd.
MS852B User’s Manual Taiwan NCC Warning Statement 低功率電波輻射性電機管理辦法 第十二條：經型式認證合格之低功率射頻電機，非經許可，公司、商號或使用者 均不得擅自變更頻率、加大功率或變更原設計之特性及功能。 第十四條：低功率射頻電機之使用不得影響飛航安全及干擾合法通信；經發現有 干擾現象時，應立即停用，並改善至無干擾時方得繼續使用。 前項合法通信，指依電信法規定作業之無線電通信。 低功率射頻電機需忍受合法通信或工業、科學及醫療用電波輻射性電機設備 之干擾。 注意事項: 1. 使用過度恐傷害視力。 2. 使用30分鐘請休息10分鐘；2歲以下幼兒不看螢幕，2歲以上每天看螢幕不要超過 1小時。 3. 減少電磁波影響，請妥適使用。 v © 2019 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd.
MS852B User’s Manual Laser Information The unitech product is certified in the U.S. to conform to the requirements of DHHS/CDRH 21CFR Subchapter J and to the requirements of IEC 825-1. Class II and Class 2 products are not considered to be hazardous. The unitech product contains internally a Visible Laser Diode (VLD) whose emissions do not exceed the maximum limits as set forth in the above regulations.
MS852B User’s Manual Battery Notice 1. To guarantee optimal performance, it is recommended that rechargeable batteries be replaced every year, or after 500 charging cycles are completed. It is normal for the battery to balloon or expand after one year or 500 cycles. Although it does not cause damage, it cannot be used again and must be disposed of according to the location's safe battery disposal procedures. 2.
MS852B User’s Manual CAUTION! RISK OF EXPLOSION IF BATTERY IS REPLACED INCORRECTLY. DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS. 如果更換不正確之電池行事會有爆炸的風險 請依製造商說明書處理用過之電池 如果更换不正确之电池行事会有爆炸的风险 请依制造商说明书处理用过之电池 Battery charge notice It is important to consider temperature when the battery pack is charging. Charging is most efficient at normal room temperature or in a slightly cooler environment. It is essential that batteries are charged within the stated range of 0°C to 40°C.
MS852B User’s Manual Storage and safety notice Although charged batteries may be left unused for several months, their capacity may be depleted due to build up of internal resistance. If this happens, they will require recharging prior to use. Batteries may be stored at temperatures between -20°C to 60°C, however they may deplete more rapidly at higher temperatures. It is recommended to store batteries at room temperature. * The message above only applies to the usage of the removable batteries.
MS852B User’s Manual Adapter Notice 1. 2. 3. 4. Please do not leave the power adapter in the socket when it is not connected to your unitech product for charging. Please remove the power adapter when the battery is fully recharged. The bundled power adapter that comes with your unitech product is not meant to be used outdoors. An adapter exposed to water or rain, or a very humid environment can cause damage to both the adapter and the product.
MS852B User’s Manual Worldwide Support unitech’s professional support team is available to quickly answer questions or assist with technical-related issues. Should an equipment problem occur, please contact the nearest unitech regional service representative. For complete contact information please visit the Web sites listed below: Taipei, Taiwan – Headquarters Europe Tel: +886-2-89121122 Tel: +31-13-4609292 E-mail: info@hq.ute.com E-mail: info@eu.ute.com Address: Address: 5F, No.
MS852B User’s Manual Warranty Policy The items covered under the unitech Limited Warranty are free from defects during normal use. The warranty period is varied from each country. Please consult with your supplier or unitech local office for actual length of warranty period to your purchased product. Warranty becomes void if equipment is modified, improperly installed or used, damaged by accident or neglect, or if any parts are improperly installed or replaced by the user.
MS852B User’s Manual Table of Contents Preface...........................................................................................................i About This Manual ........................................................................................ i Regulatory Compliance Statements .............................................................. i Laser Information ........................................................................................ vi LED Information .......................
MS852B User’s Manual Chapter 1 - Overview 1.1 Package Please make sure the following contents are in the MS852B gift box. If something is missing or damaged, please contact your unitech representative.
MS852B User’s Manual 1.2 Product Detail ￭ Scanner details - 2 - © 2019 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd.
MS852B User’s Manual ￭ Cradle details USB (Left) - 3 - © 2019 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd.
MS852B User’s Manual 1.3 Specifications Optical & Performance 1D or 2D 2D Sensor CMOS sensor with 640 x 400 pixel Aiming Element 610nm Illumination Hyper Red 660nm Ambient Light 10000 ft. candles (107,639 lux) Skew Angle ± 60° Pitch Angle Sensor ± 60° Roll Angle 0 - 360° Optical Resolution 5.0 mil (Code 39), 6.6 mil (PDF417) Printing Contrast Scale Minimum 20% Depth of Field (DOF PCS=80%) SYMBOLOGY / X-DIM TYPICAL RANGE* Near Far 5 mil Code 39 2.0 in / 5.1 cm 6.4 in / 16.
MS852B User’s Manual Mechanical Scanner Dimension 87.8 mm x 177.7 mm x71.6 mm (L x H X W) Cradle Dimension 120.6 mm x 86.0 mm x 88.
MS852B User’s Manual 1.4 Getting Started ￭ How to pair devices with MS852B Please scan the barcode below to begin pairing. The scanner will show solid blue when it is pairing. BT/BLE Un-Pair / Pair ￭ How to pair devices with MS852B on the cradle If the MS852B has already paired, please scan the barcode below to un-pair it first then put it on the cradle to start pairing.
MS852B User’s Manual 1.5 Battery Charging When you receive the package and use the MS852B for the first time, you will need to fully charge the battery. It takes approximately 5 hours to fully charge the battery. To charge the scanner with / without a cradle, please follow the instructions below. To charge MS852B, please connect USB type C cable to the USB port of a host PC.
MS852B User’s Manual 1.
MS852B User’s Manual ￭ Cradle LED indicator Description Indication Power off N/A Power on & Host is not connected Solid Red Host is connected and BT is waiting for pairing. Blue LED toggling every second Host is connected and BT is paired & ready for connection Solid Green Host & BT are connected Solid Blue Cradle in Bootloader Mode For FW update only White LED BT is connect & its signal is weak than Blue flashing quickly normal - 9 - © 2019 unitech Electronics Co., Ltd. All rights reserved.
