because we care MS650 Wireless CCD Ring Scanner Quick Guide For more detailed scanner setting, please go to www.ute.com to download the user manual. Version 1.
FCC WARNING STATEMENT This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
BEEPER INDICATION INTRODUCTION Micro USB port LED Indicator (with Protective Cover) Function Button Restart Button (insert pin into the hole) Exit Window Touch-Activated Trigger Button SPECIFICATIONS Sensor Resolution Indicator PCS Housing Profile Battery Life Charge Time Radio Coverage Symbologies Linear Image Sensor 4mil/ 0.1mm LED, Buzzer 30% Plastic(PC+ABS) BT HID, USB HID, USB VCP, Batch Mode 6000 scans (1 scan/ 5 sec) 2.5 hours (fully charged) Bluetooth 4.1 (Class2) 10M/33ft.
OUT OF THE BOX CHARGING THE BATTERY Host Scanner USB A Wireless CCD Ring Scanner USB Charger Cable MS650 Wireless CCD 1 Ring Scanner 2 Quick Guide because we care Regulatory Compliance Statements Part No. XXXXXXX FCC Warning Statement This device has been tested and found to comply with for a Class B digital device, the limits pursuant to part 15 of the FCC rules. These limits are designed ion against harmful interference to provide reasonable protectin a residential installation.
STEP 1 - GETTING STARTED 1. Pull open the long strap and insert your index finger through the loop. 3. Clench your fist and use your thumb to tap the touch-activated trigger button. 2. Adjust and attach the long strap for a comfortable fit. 4. Aim at the barcode you wish to scan.
STEP 2 - BUTTON PREFERENCE Scan one of below configuration barcodes to determine which touch-sensing button to enable according to your habit: . F064$ *.F064$* *.F065$* *.F066$* Right Button Only [ For Left-handed User ] . F065$ STEP 3 - INTERFACE SELECTION Scan one of below configuration barcodes to determine your interface: . E043$ BT HID [ Recommended ] USB HID Left Button Only . C006$ [ For Right-handed User ] USB VCP . F066$ Both Buttons *.E043$* *.C008$* . C008$ *.C006$* .
BT - HID GETTING CONNECTED 1. Scan [Disconnect] to delete previous pairing record. Alternatively, you may long-press the function button for 5 seconds until the the scanner emit two beeps. . E031$ *.E031$* *.E043$* *.F068$* *.F067$* Disconnect BT - HID SMARTPHONE/TABLET TOUCH KEYBOARD Please follow below instruction to toggle touch keyboard on smartphone/tablet. iOS To toggle iOS touch keyboard, please simply press the function button. 2. Scan [BT - HID]; the scanner will emit two beeps.
BT - HID POWER OFF TIMEOUT NUMERIC BARCODES The period of inactivity before auto power-off. Variable Timeout . B030$ *.B030$* *.B029$* SET MINUTE (Range: 00 ~ 60) . B029$ SET SECOND (Range: 00 ~ 60) The default timeout is 00 minute and 30 seconds. For example, to set the timeout as 5 minutes 30 seconds: 1. Scan [Set Minute] 2. Scan [0] & [5] on page 14. 3. Scan [Set Minute] 4. Scan [Set Second] 5. Scan [3] & [0] on page 14. 6. Scan [Set Second] No Timeout (Scanner Always On) . B021$ *.
GENERAL SETTINGS ILLUMINATION PREFERENCE . A001$ . F059$ DEFAULT LASER ALWAYS ON LED ON AFTER 1 SEC ABORT LASER ALWAYS ON LED AUTO-ADAPTIVE CHECK VERSION LASER ALWAYS ON LED ALWAYS ON . P023$ *.F059$* *.F049$* *.F048$* *.F046$* . F049$ . A007$ BEEPER . F048$ . F046$ LASER OFF LED ALWAYS ON . F018$ BEEP ON .
KEYBOARD LAYOUT . C010$ ENGLISH (USA) JAPAN (106 key) ENGLISH (UK) CANADIAN (FRENCH) FRENCH CANADIAN (TRADITIONAL) . C018$ . C009$ . C025$ . C034$ . C012$ . C029$ . C011$ GERMAN NORWEGIAN . C026$ . C014$ ITALIAN SWEDISH . C031$ .
KEYBOARD LAYOUT . C017$ CZECH (QWERTY) BELGIAN (AZERTY) . C030$ . C028$ . C022$ CZECH (QWERTZ) DUTCH . C027$ . C021$ HUNGARIAN (QWERTZ) DANISH . C032$ . C024$ HUNGARIAN (101 KEY) SLOVAK SWISS (GERMAN) BRAZILIAN (PORTUGUESE) . C033$ . C016$ . C023$ SWISS (FRENCH) - 19 - .
ENABLE SYMBOLOGIES . G010$ . A002$ ENABLE ALL CODE CODE 93 . N017$ . K010$ CODE 32 IATA . L014$ . L010$ UK PLESSEY TELEPEN . L001$ . N032$ MSI GS1 DATABAR INDUSTRIAL 2 OF 5 GS1 DATABAR LIMITED MATRIX 2 OF 5 GS1 DATABAR EXPANDED . N010$ . N001$ . M010$ - 21 - .
TERMINATOR BATCH MODE . D012$ CR . D011$ LF . D013$ CR + LF . D010$ NONE . C035$ BATCH MODE *.c035$* After scanning the above barcode, the scanner will be able to collect barcode data off-line. The barcode data will be stored in the format of: < Date >, < Time >, < Barcode Data > < CR > To retrieve stored data, please connect the scanner to the host with cable, access removable storage device “MiniScan” from which you may open or copy the file “BARCODE.txt” to your computer.
BATCH MODE DATE & TIME SETUP BATCH MODE DATA FORMAT . R011$ . R006$ *.R006$* SET DATE Example: To set Date to 2017-08-01 (Year-Month-Day): 1. Scan [Set Date] 2. Scan [1], [7], [0], [8], [0], [1] on page 14. 3. Scan [Set Date] DATA FORMAT *.R011$* The default Data Format is ,
BATCH MODE DATE FORMAT BATCH MODE . R008$ *.R008$* TIME FORMAT . R009$ DATE FORMAT TIME FORMAT *.
HOW TO REMOVE VELCRO STRAP 1. Pull open the long strap. 3. Pull open the short strap on the other side. 2. Pull out the long strap through the slot. 4. Keep pulling the short strap until the whole velcro strap is removed from the scanner.
HOW TO INSTALL VELCRO STRAP (RIGHT HANDED USER) 1. Insert the long strap through the left slot, with velcro side facing downwards. 3. Insert the long strap through the other slot, with velcro side facing upwards. 2. Pull the long strap to the end. 4. Attach the long strap to itself to close.
HOW TO INSTALL VELCRO STRAP (LEFT HANDED USER) 1. Insert the long strap through the right slot, with velcro side facing downwards. 3. Insert the long strap through the other slot, with velcro side facing upwards. 2. Pull the long strap to the end. 4. Attach the long strap to itself to close.
TROUBLESHOOTING TEST BARCODES Code 39 CODE-39 TEST Interleaved 2 of 5 9876543210 Code 128 12345678 Q: Your Bluetooth is unable to detect the scanner. A: (1) Make sure your Bluetooth version is 4.0 or later. (2) Restart your Bluetooth or Host device and try again, following the instruction on page 11. (3) Make sure the scanner is in BT-HID mode (see page 10). If the scanner is discoverable, its LED indicator will be flashing Blue. (4) The scanner might be powered off.
