User's Manual
Table Of Contents
- 1.0 INTRODUCTION
- 2.0 FEATURES & OPTIONS
- 3.0 SAFETY WARNINGS
- 4.0 WARRANTY (summary)
- 5.0 UNPACKING AND INSPECTION
- 6.0 GENERAL SPECIFICATIONS
- 7.0 PRINCIPAL OF OPERATION
- 8.0 FRONT PANEL DESCRIPTION
- 9.0 REAR PANEL DESCRIPTION
- 10.0 LED Indicators
- 11.0 MAKING CONNECTIONS TO THE X75
- 12.0 INSTALLATION
- 13.0 USING THE CONTROLLER WEB BROWSER INTERFACE
- Appendix 1 – SNMPv3 MIB Information
- Appendix 2 – Load LVD (special order)
- Appendix 3 – Revision History
- Figure 1 - X75 Compact Integrated DC Power System
- Figure 2 - Block Schematic
- Figure 3a - Front View with Breakers (configuration A)
- Figure 3b - Front View with GMT Fuses (configuration B)
- Figure 4 - Rear Views of Base and Expansion Units
- Figure 5 - LED Indicators
- Figure 6 - Recommended Load Circuit Wire Sizes
- Figure 7 - Battery Temp. Probe & Alarm Relay Connector Pin-Out
- Figure 8 - Ethernet Connector Pin-Out
- Figure 9 - Auxiliary Connector Pin-Out
- Figure 10 - Input Current Ratings
- Figure 11 - Status WEB Page (typical)
- Figure 12 - Rectifier Status WEB Applet (typical)
- Figure 13 - Installation WEB Applet - system tab (typical)
- Figure 14 - Installation WEB Applet - float & tc tab (typical)
- Figure 15 - Installation WEB Applet - battery tab (typical)
- Figure 16 - Installation WEB Applet - float & tc tab (typical)
- Figure 17 - Installation WEB Applet - lvd tab (typical)
- Figure 18 - Installation WEB Applet - digital i/p tab (typical)
- Figure 19 - Installation WEB Applet - rectifiers tab (typical)
- Figure 20 - Installation WEB Applet - shunts tab (typical)
- Figure 21 - Battery Management WEB Applet (typical)
- Figure 22 - Alarm Matrix WEB Applet (typical)
- Figure 23 - Alarm Matrix WEB Applet - matrix options (typical)
- Figure 24 - Alarm Matrix WEB Applet - temperature alarm settings (typical)
- Figure 25 - Alarm Matrix WEB Applet - voltage alarm settings (typical)
- Figure 26 - Alarm Matrix WEB Applet - voltage alarm settings (typical)
- Figure 27 - Alarm Matrix WEB Applet - other alarm settings (typical)
- Figure 28 - Network Settings WEB Applet (typical)
- Figure 29 - Alarm Log WEB Applet (typical)
- Figure 30 - Data Log WEB Applet (typical)
- Figure 31 - Change Password WEB Applet
- Figure 32 - Help WEB Page
- Figure 33 - About WEB Page (typical)
Page 61
X75 SERIES - Mk3 Controller
INSTALLATION & OPERATING MANUAL
Manual No. x75mk3-11
x75-man-Rev11-0815.indd
Parameter Name Function
digitalxTrapOn Digital Input x is in an alarm state. [1 only in X75]
digitalxTrapOff Digital Input x alarm has cleared. [1 only in X75]
nRectTrapOn There are insufcient rectiers in the system.
nRectTrapOff There are sufcient rectiers in the system.
acfTrapOn An AC Failure has been detected.
acfTrapOff An AC Failure alarm has cleared.
rectTHATrapOn A Rectier Thermal Alarm has been detected.
rectTHATrapOff A Rectier Thermal Alarm has cleared.
rectFANTrapOn A Rectier Fan Failure Alarm has been detected.
rectFANTrapOff A Rectier Fan Failure Alarm has cleared.
singleRFATrapOn A single rectier failure alarm has been detected.
singleRFATrapOff A single rectier failure alarm has cleared.
multiRFATrapOn A multiple rectier failure alarm has been detected.
multiRFATrapOff A multiple rectier failure alarm has cleared.
eqTrapOn An equalization has been activated.
eqTrapOff An equalization has stopped.
bTestTrapOn A battery test has been activated.
bTestTrapOff A battery test has ended.
bProbexDisTrapOn Battery Temperature Probe x has been disconnected. [1 only in X75]
bProbexDisTrapOff Battery Temperature Probe x has been reconnected. [1 only in X75]
bProbexShortTrapOn Battery Temperature Probe x has become shorted. [1 only in X75]
bProbexShortTrapOff Battery Temperature Probe x is no longer shorted. [1 only in X75]
eProbeDisTrapOn External Temperature Probe has been disconnected.
eProbeDisTrapOff External Temperature Probe has been reconnected.
eProbeShortTrapOn External Temperature Probe has become shorted.
eProbeShortTrapOff External Temperature Probe is no longer shorted.
battTestFailTrapOn A battery test has failed.
battTestFailTrapOff A battery test failure alarm has been cleared.
coldStart The SNMP agent has restarted.
The X75 will issue a trap for any of the conditions mentioned above.
To obtain a copy of the latest X75 MIB download it from:
http://unipowerco.com/MIB_les/Unipower-Controller2-MIB.txt