User's Manual
Table Of Contents
- 1.0 INTRODUCTION
- 2.0 FEATURES & OPTIONS
- 3.0 SAFETY WARNINGS
- 4.0 WARRANTY (summary)
- 5.0 UNPACKING AND INSPECTION
- 6.0 GENERAL SPECIFICATIONS
- 7.0 PRINCIPAL OF OPERATION
- 8.0 FRONT PANEL DESCRIPTION
- 9.0 REAR PANEL DESCRIPTION
- 10.0 LED Indicators
- 11.0 MAKING CONNECTIONS TO THE X75
- 12.0 INSTALLATION
- 13.0 USING THE CONTROLLER WEB BROWSER INTERFACE
- Appendix 1 – SNMP MIB Information
- Appendix 2 – Load LVD Configuration (model X75-12-A-GHHIL-S-578 only)
- Appendix 3 – Revision History
- Figure 1 - X75 Compact Integrated DC Power System
- Figure 2 - Block Schematic
- Figure 3a - Front View with Breakers (configuration A)
- Figure 3b - Front View with GMT Fuses (configuration B)
- Figure 4 - Rear Views of Base and Expansion Units
- Figure 5 - LED Indicators
- Figure 6 - Recommended Load Circuit Wire Sizes
- Figure 7 - Battery Temp. Probe & Alarm Relay Connector Pin-Out
- Figure 8 - Ethernet Connector Pin-Out
- Figure 9 - Auxiliary Connector Pin-Out
- Figure 10 - Input Current Ratings
- Figure 11 - Controller Status WEB Page (typical)
- Figure 12 - Rectifier Status WEB Page (typical)
- Figure 13 - Rectifier I²C Addressing
- Figure 14 - Controller Factory Calibration WEB Page (typical)
- Figure 15 - Controller Site Installation WEB Page (typical)
- Figure 16 - Alarm Configuration WEB Page (typical)
- Figure 17 - Controller Network Settings (typical)
- Figure 18 - Controller Alarm Log WEB Page (typical)
- Figure 19 - Controller Control Panel WEB Page (typical)
- Figure 20 - Controller System Settings WEB Page (typical)
- Figure 21 - SNMP Configuration WEB Page (typical)
- Figure 22 - Controller Help WEB Page (typical)
- Figure 23 - About UNIPOWER Telecom WEB Page (typical)
Page 7
X75 SERIES
INSTALLATION & OPERATING MANUAL
Manual No. x75-10b
x75-man-Rev10b-0514.indd
3.6 The controller unit integral to the X75 is tted with a replaceable battery.
CAUTION: RISK OF EXPLOSION IF BATTERY IS REPLACED BYAN
INCORRECTTYPE.DISPOSEOFUSEDBATTERIESACCORDINGTO
THEINSTRUCTIONS.
4.0 WARRANTY (summary)
X75 Series DC power systems are warranted for two (2) years from date of shipment
against defects in material and workmanship. This warranty does not extend to products
which have been opened, altered or repaired by persons other than persons authorized by
the manufacturer or to products which become defective due to acts of God, negligence or
the failure of customer to fully follow instructions with respect to installation, application
or maintenance.
For a complete text of UNIPOWER’s warranty conditions please request a copy from your
local Sales Ofce.
5.0 UNPACKING AND INSPECTION
5.1 This X75 DC power system was carefully tested, inspected and packaged for shipment
from our factory. Upon receipt the unit should be carefully unpacked and inspected
for any damage in shipment.
5.2 If there is evidence of damage, donotattempttoinstalltheunit. The freight carrier
should be notied immediately and a claim for the cost of the X75 should be led
with the carrier for direct reimbursement. Be sure to include the model and serial
number of the damaged unit in all correspondence with the freight carrier. Also
save the shipping carton and packing material as evidence of damage for the freight
carrier’s inspection.
5.3 UNIPOWER will cooperate fully in case of any shipping damage investigation.
5.4 Always save the packing materials for later use in shipping the unit. Never ship the
system or the rectier modules without proper packing.