Uniq 2 Air Purifier User’s Manual
UniqAir Oy (2626040-9) Tuomikatu 28 53810 Lappeenranta www.uniqair.fi info@uniqair.fi Document version: 1.0 UniqAir reserves the right to make changes The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by UniqAir Oy is under license. Other trademarks and trade names are those of their respective owners. Wi-Fi® is a registered trademark of Wi-Fi Alliance®.
Table of Contents 1 SAFETY INSTRUCTIONS 2 2 PRODUCT DESCRIPTION 3 2.1 2.2 2.3 3 3.1 3.2 3.3 3.4 4 4.1 4.2 5 5.1 5.2 5.3 5.4 6 6.1 6.2 7 7.1 7.2 7.
1 Safety Instructions Read this manual carefully before use. Use the device only as instructed in this manual. The operating instructions do not cover all possible operating situations or conditions. The manufacturer is not liable for personal injury or damage to property resulting from improper use. General safety instructions: • Only use UniqAir approved filters and replacement parts. • Do not place the device higher than two meters from ground. • Do not block or cover the air inlet or outlet.
2 Product Description UniqAir Uniq 2 is an efficient air purifier designed for indoor air. The Uniq 2 air purifier can be controlled manually or by a mobile device via Bluetooth® connection. Air is pulled in from the outer edge of the circular aluminum frame and the air outlet is located at the front side of the device.
2.2 Technical Specifications Model UniqAir Uniq 2 Operating voltage 220– 240 V Dimensions Height 450 mm Width 445 mm Depth 185 mm Frequency 50/60 Hz Dimensions with stand Height 534 mm Width 445 mm Depth 217 mm Max power consumption 78 W Dimensions with wall mount Height 467 mm Width 445 mm Depth 200 mm Operating temperature 0–60 C Weight (with filters) 9 kg WiFi standards IEEE 802.11 b/g/n Noise-level 27-64 dB(A) WiFi frequency 2.
3 3.1 Setup Unpacking Carefully remove the device from its plastic cover. After attaching the stand or optional wall mount (section 3.2), remove the film covering the glass front panel by peeling it gently from the tab at the top. See section 5.4 for instructions on recycling the packaging material. 3.2 Attaching the Stand or Wall Mount a) Stand 1. Place the device on a flat clean surface with the glass panel facing down and be careful of not scratching the glass. 2.
b) Wall Mount (optional) 1. Use four screws to attach the wall mount to the desired place on a wall. 2. Use two screws to attach the base of the Uniq 2 device to the wall mount. See the adjacent image. WARNING! Provided mounting screws should be used only with hard materials like wood and concrete. 3.3 Positioning the Device To ensure the greatest effectiveness, make sure that the airflow is as unobstructed as possible in front and on the sides of the device.
3.4 Connecting the Power Cord 1. 2. 3. Check that the power cord is externally intact. If the cord is damaged, contact UniqAir’s customer service. Connect the power cord to the connector on the bottom of the device as shown on the picture below. Plug the other end of the power cord into a grounded electrical outlet. NOTE! The mains voltage of the outlet must correspond to the voltage indicated on the type plate. WARNING! Electrical safety hazard. Only connect the appliance to a grounded outlet.
4 Operating the device The basic functionalities of the device, such as purification power and brightness of the lights, can be controlled directly from the capacitive buttons on the glass front panel. Adding timers, monitoring the condition of the filter, performing updates, and many other features require the use of a mobile application. Both usage methods will be presented in the following sections. 4.
The device can be operated manually with the buttons on the glass front panel. 1. If none of the lights on the power range indicator are on, start the device by pressing the plus button. The device will start working at level 1, indicated by the first light turning blue. 2. Adjust the purification power to desired level using the plus and minus buttons. The round power range indicator shows the selected power setting.
5 Service and Maintenance IMPORTANT! Turn the device off and unplug the power cord before performing any maintenance. The fan will not stop rotating immediately: after switching the device off, wait a moment before starting maintenance work. 5.1 Replacing the prefilter We recommend a prefilter change interval of 4-6 months when the device is in continuous use. The prefilter can also be vacuumed and/or washed if necessary, enabling a longer change interval.
5.4 Recycling NOTE! Always follow local regulations when disposing of the device, its parts, or the transport packaging. Transport packaging The transport packaging of the air purifier is completely recyclable. Sort the packaging parts (cardboard, plastic) into the appropriate collection containers. Prefilters Dispose of used prefilters as energy waste. Main filters We recommend that you return used main filters to your UniqAir contact person or reseller.
6 Troubleshooting 6.1 Problems and Possible Solutions The touch buttons on the control panel do not respond and/or the fan does not start or change power level. • Disconnect and reconnect the power cord to the outlet. If this does not help, reset the device to factory settings according to section Error! Reference source not found. instructions. Adding the purifier to the UniqAir Uniq application for the first time fails.
6.2 Restoring the Device to Factory Settings To fix possible malfunctions, the device can be restored to factory settings. This will clear the Wi-Fi settings, Bluetooth® bonding, timers, and other user data stored in the device’s memory. All device firmware updates will be removed, and the device will revert to its original factory version. To restore factory settings, follow these steps: 1. 2. 3. 4. 5. 6.
7 Annexes 7.1 Colors of the Bluetooth®-button The multicolored light of the Bluetooth® button indicates the status of the device's Wi-Fi and Bluetooth® connection. Below are the explanations for the different colors. White The device is not connected to a Wi-Fi access point. Blinking white Bluetooth® pairing mode is enabled. Blinking blue Device is trying to connect to a Wi-Fi access point. Blue Wi-Fi-is successfully connected. Red Fault. The most common cause is an incorrect Wi-Fi password.
7.2 Warranty conditions These warranty conditions apply to all new UniqAir air purifiers. 1. UniqAir air purifiers have a manufacturer's warranty. 2. The warranty is two (2) years from the date of delivery of the product. 3. The warranty covers defects and faults that occur during the warranty period due to manufacturing defects or faults in the product’s materials. 4. The warranty only applies to air purifiers used indoors or in equivalent weather-protected conditions to filter air impurities.
7.3 Replacing the Main Filter 1. Unplug the air purifier. 2. Place the purifier on a flat surface with the glass panel facing down. NOTE! If you place the air purifier on a hard surface, you should protect the glass panel with a cloth or other soft material.
3. Using a cross-head screwdriver, turn the rear cover quick-release screws (4 screws) 90 degrees counterclockwise, until the screws pop out. 4. After loosening all four quick-release screws, lift the back cover vertically upwards. NOTE! The quick-release screws should remain in the holes in the back cover. 5. Remove the EPP disc from on top of the filter and lift the filter out of the air purifier. 6.
