Instructions

ManualsBrandsUnion Rustic ManualsBedsAideliz Solid Wood Platform Bed

PARTS

(4) F-15 PROP - 15”

(4) F-37 BED RAIL - 37”

(10) F-48 MIDDLE SLAT - 48”

(4) F-32 SLAT CAP - 32"

PARTS LIST

BED RAIL

F-37

PROP

F-15

F-44

PROP CONNECTOR

F-32

SLAT CAPS

F-52

BED SLATS

H-11

WOOD DOWEL

H-19

1 - 3/4” WOOD SCREW

F-10

LEG

F-6

RAIL CONNECTOR

F-48

MIDDLE SLATS

(2) F-6 RAIL CONNECTOR - 6”

(4) F-52 BED SLAT - 52”

(2) F-44 PROP CONNECTOR - 44”

(2) F-10 LEG - 10”

Tools needed:

#2 Phillips Screw Driver

This bed frame is made with Tulip Poplar. Any green tint in the wood will change to light brown in a

few weeks. This will happen in 20 to 30 minutes if placed in direct sunlight. Tulip Poplar can be left

unfinished, clear finished, stained, or painted. I prefer the lighter stains over the darker ones

because the wood is fairly porous. My favorite is a clear finish with no stain. Satin polyurethane (oil

or water based) works well.

Painting: It is best to start with an interior primer and lightly sand before painting.

Staining: Lightly sand before staining. Wipe stain on with a rag until you get the desired color. If

you are going to use a top coat (such as polyurethane), do not sand again until after the first coat,

and then be careful not to sand away the stain.

Finishing: All finishes work well with Tulip Poplar. A simple wax finish over stain (Minwax for

example) is easy. An oil finish such as Danish oil can be used. Or a clear top coat such as

polyurethane works well to seal the wood. With polyurethanes, the first coat acts as a sanding

sealer. So you should lighty sand (180 - 220 grit sandpaper) after the first coat, wipe the wood clean,

and then build up coats for the desired effect.

H-8

2-1/4” CLEVIS PIN

H-5

HAIR PIN

H-12

3-1/4” CLEVIS PIN

We warrant all of its products for five years against any defects that are due to faulty materials or

workmanship. We will promptly correct such defects by repair or replacement, at our option, without charge.

This warranty covers product defects only and will expire five years after date of purchase by the original

consumer purchaser, with proof of purchase required.

This warranty does not apply to damage caused by and resulting from misuse, neglect, accident, or

improper operation, maintenance, storage, transportation, or handling of the product. This warranty is for the

original consumer purchaser for residential use only and does not apply if the product is used in any

commercial application (such as rental property). This warranty does not cover any incidental or consequential

damages. If you feel that you have a claim under this warranty, please contact the store from which it was

purchased. If this is not possible, call us

for advice on handling your claim.

Full

Instructions for FOLD Bed

Summary of content (4 pages)

PAGE 1
Instructions for FOLD Bed Full Tools needed: #2 Phillips Screw Driver This bed frame is made with Tulip Poplar. Any green tint in the wood will change to light brown in a few weeks. This will happen in 20 to 30 minutes if placed in direct sunlight. Tulip Poplar can be left unfinished, clear finished, stained, or painted. I prefer the lighter stains over the darker ones because the wood is fairly porous. My favorite is a clear finish with no stain. Satin polyurethane (oil or water based) works well.
PAGE 2
Push Wood Dowels (H-11) all the way into holes on the edge of the (4) Props (F-15) and the (4) Bed Rails (F-37). 1 3 H-8 Be sure that the Prop Connector goes below the Bed Rail. Attach two of the Bed Rails (F-37) to the outside of one of the Prop Assemblies using 2-1/4” Clevis Pins (H-8). H-11 Let the Prop Assembly swing down so that the Prop Connector can go below the Bed Rails. Secure the Clevis Pins with Hair Pins (H-5). F-15 PROP Repeat these steps to make the other half of the bed frame.
PAGE 3
5 6 Assemble the Slat Decks by pressing (5) Middle Slats (F-48) into (2) Slat Caps (F-32). Then press (2) Bed Slats (F-52) onto the Slat Caps. Repeat for the other Slat Deck. Push the Slat Decks down onto the Wood Dowels and attach with Wood Screws (H-19). H-19 F-32 F-48 7 F-52 Note: Be sure that the 4 dowel holes are on the bottom. Push (2) “Wood Dowels (H-11) all the way into the holes on the bottom of the Bed Rails on just one end of the bed.
PAGE 4
Operation: 1 2 Fold up Prop assemblies. 3 Fold Bed Rails together. To secure bed in the folded position, push the Wood Dowels into holes on the Bed Rails from the other side.