Owner Manual

ManualsBrandsUnion Rustic ManualsAll Patio TablesHaddie Solid Wood 6 - Person Dining Table

Table Of Contents

Caution : You must read this before you proceed

TABLE

CAUTION: This Table is NOT a TOY.

Keep your child / children at bay during the assembly process.

For moving the Table and to prevent damage to the Table, two adults are

needed to execute this action.

Page 1 of 9

Please look in the

ron

eg for hardware packs.

Summary of content (9 pages)

PAGE 1
Caution : You must read this before you proceed Please look in the iron leg for hardware packs. TABLE CAUTION: This Table is NOT a TOY. Keep your child / children at bay during the assembly process. For moving the Table and to prevent damage to the Table, two adults are needed to execute this action.
PAGE 2
Label Picture Description QTY A Table Top 1 B Iron Leg 2 C Support Bar 2 D Side Turnbuckle Set 2 E Bottom Turnbuckle Set 1 Label Picture Description QTY 11 Short Bolt (M8x20mm) 17 22 Washer 17 3 Long Bolt (M6x45mm) 4 Screw (M6x50mm) 5 Sleeve Nut (M6x20mm) 3 6 Allen Key 2 3 13 Page 2 of 9
PAGE 3
Before Beginning Assembly: Page 3 of 9
PAGE 4
OVERVIEW Table Top (A) Side Turrnbuckle Set (D) Side Turnbuckle Set (D) Bottom Turnbuckle Set (E) Iron Leg (B) Iron Leg (B) FRONT FACING This Table has multiple parts and may require up to some 30 minutes to assemble. To give you an overview of the Table parts, the above picture is to help you put the various parts into perspective. Please read through the instructions below to familiarise yourself with the parts and steps before assembly.
PAGE 5
Step 2 D D Step 2.1 Step 2.2 E E E 2.1) Connect the Side Turnbuckle Sets(D) together as shown in the arrow above 2.2) Connect the Bottom Turnbuckle Set(E) together as shown in the arrows above Step 3 Step 3.1 A Step 3.2 3.1) With the assistance of an adult helper, unfold the Table Top(A) as shown. 3.2) Then lay the Table Top (A) facedown onto a clean, flat surface to avoid any scratches or damage to the product.
PAGE 6
Step 4 6 4 housings C A Align Support Bar(C) to the housings on Table Top(A) and secure using Screws(④) with Allen Key(⑥). Only loosely tighten the Screws. Repeat the same process with the other Support Bar(C). Step 5 6 B 1 2 A Attach Iron Leg(B) to Table Top(A) using Short Bolt(①) and Washer(②) with Allen Key(⑥). Notice: The leg with hole should be face inside against Only loosely tighten the Bolts.
PAGE 7
Step 6 B D 2 1 6 A Place Side Turnbuckle Set(D) between housing of Table Top(A) and Iron Leg(B). Attach Side Turnbuckle Set(D) to Iron Leg(B) using Short Bolt(①) ① and Washer(②) with Allen Key(⑥) Only loosely tighten the Bolts. Repeat the same process with the other Side Turnbuckle Set(D). Step 7 6 5 3 D 6 A ③ and Sleeve Affix Side Turnbuckle Set(D) to Table Top(A) using Long Bolt(③) Nut(⑤) with Allen Key(⑥). Only loosely tighten the Bolts.
PAGE 8
Step 8 2 1 E 6 Attach the Bottom Turnbuckle Set(E) to Iron Legs(B) using Short Bolt(①) and Washer(②) with Allen Key(⑥). Only loosely tighten the Bolts. Step 9 Stand the Table right side up. Inspect it and make sure all parts are adequately connected. In a sequential manner, tighten all Bolts and Screws until fully locked into position.
PAGE 9
Page 9 of 9