Console assembly gu de 1
ntroduct on Valued Customer, We des gn and carefully manufacture our products for our customers, We w sh that our customers to have fun wh le they are do ng the r new furn ture The product you just purchased was subjected to all sorts of tests and controls before send ng out to you. Hope you enjoy your new furn ture!!! Before start ng, please check all components and accessor es accord ng to the prov ded l st.
before you start o or Get requ red nstallat on tools prepared. Do not nstall the product on rough surfaces.
components Part1 Part2 Part3 Part4 Part5 Part6 Part7 Part8 Part9 Part10 Part11 Part12 TOTAL 01 07 05 08 03 04 1x 1x 2x 1x 1x 1x 2x 2x 1x 2x 2x 1x 17x 08 11 03 02 10 07 11 10 06 12 09 A04 dowel Ø8 K01 A13 C04 C05 half overlay bracelet D01 15x A02 minifix head 21x A05 shelf pin D01 A40 A04 A02 nail 4x A07 18 mm sticker A03 minifix screw 21x C03 12x 4x 4x 50 mm screw 128 mm handle pivot 4x A09 30x 8x c1 36x bracelet 3.
gett ng fam l ar w th the ma n components *Minifix is the main connec on component used in Decoro ka products.Before star ng, please check the below figures MINIFIX HEAD MINIFIX SCREW DOWEL *Please not ce that there s an small arrow on A02 (m n fix head).Th s arrow should show the d rect on of upper hole. *After attach ng two p eces please turn the A02 (m n fix head) clockw se d rect on w th the help of a screwdr ver.
step a 1 *Please nsert A03 (m n fix screw) nto the holes on the p ece #7 and #8 as shown below *Please nsert A02 (m n fix head) nto the holes on the p eces #2,#4 and #5 as shown below *Make sure that all the arrows on A02 (m n fix head) are n correct d rect on 21x A02 2 4 8 5 2x 7 2x 12x A03 6
2 step b *Please attach the p ece #5 between the p eces #7 and #8 as shown below *Now screw the A02 (m n fix head) clockw se d rect on w th the help of screwdr ver. 7 5 8 7 5 8 3 step c *Please attach the p eces #9 and #12 to the p ece #6 as shown below *Now screw the A13 (50 mm screw) clockw se d rect on w th the help of screwdr ver.
4 step d *Please attach the parts we nstalled n step b to the p ece #9 as shown below *Now screw the A13 (50 mm screw) clockw se d rect on w th the help of screwdr ver. 5 2 9 A13 6x 5 step e *Please attach the p ece #4 onto the p ece #9 as shown below *Now screw the A13 (50 mm screw) clockw se d rect on w th the help of screwdr ver.
6 step f *Please nsert A03 (m n fix screw) nto the holes on the p ece #1 as shown below *Please nsert A04 (dowel) nto the holes on the p ece #1 as shown below 9x 4x A03 A04 1 7 step g *Please attach the p ece #1 onto the top of the furn ture as shown below *Now screw the A02 (m n fix head) clockw se d rect on w th the help of screwdr ver.
8 step h *Please na l down A05 (shelf p n) on the holes on the p eces #2,#4 and #5 w th the help of an hammer *Please put all the C04 (p vot ) the way that they w ll fit the pre-dr lled holes on the p ece #9 *Now take A09 (3.
9 step *Please put all C05 (half overlay bracelet) nto the b g holes on p eces #10 and #11 the way they w ll fit the pre-dr lled holes *Now take A09 (3.5x18 screw ) and put them on pre-dr lled holes then turn them all w th screwdr ver C05 A09 10 11 10 step j *Please put all C03 (bracelet) nto the b g holes on p eces #10 and #11 the way they w ll fit the pre-dr lled holes *Now take A09 (3.
step k 11 *Please connect C04(p vot) and C03 (bracelet) ,C05(half overlay bracelet) as shown n figure *Turn the screw A *You can make some adjustment w th screw B for better open ng and clos ng of door 11 11 10 1 2 A= menteşe bağlama vidası B = kapak ayar vidası / to connect the hinge to the door oklar kapağın ayarlama yönünü gösterir. / to arrange the door arrows to show the directions for arrangement of doors.
12 step l *Please put the p eces #3 onto the A05 (shelf p n ) as shown below .
step n 14 *Please put A31(M4x22 handle screw) nto the holes on the p eces #10 and #11 as shown below then attach the K01 (128 mm handle) *Now turn A31(M4x22 handle screw) clockw se d rect on w th the help of screwdr ver.
step o *For the best appearance of your furn ture please place all A07(18 mm st cker) onto the A13 (50 mm screw) and A02(m n fix head).
final look 16
