Assembly Instruction

2of3
STEP 3 Install Nipple to Crossbar-
A. Thread one Hex Nut (CC) to the middle of the Nipple (DD). Place the
Lock Washer (BB) over the Nipple (DD) and then thread the Nipple
(DD) into the Crossbar (AA) until the Nipple (DD) is about 0.375”
above the Crossbar (AA).
B. Place the Ceiling Canopy (HH) over the end of the Nipple (DD)
against the ceiling to determine the correct position of the Nipple
(DD). Thread the Mounting Ball (EE) onto the Nipple (DD). Adjust
the Nipple (DD) to allow the Ceiling Canopy (HH) to rest against the
ceiling when held in place by the Mounting Ball (EE).
C. Remove the Mounting Ball (EE) and the Ceiling Canopy (HH).
Tighten the Hex Nut (CC) against the Crossbar (AA) to secure in
place.
AA
BB
CC
DD
Step A
Figure 3
HH
EE
STEP 4 - Attach the Lanyard
A. The purpose of the lanyard is to provide a means to support the
fixture hands free from the junction box while connecting the
electrical wires.
B. Turn the Button Stop so it may be inserted into a Crossbar slot. Make
sure the Button Stop is completely inside the Crossbar. Slowly
release the fixture to make sure it is supported by the Button Stop.
Proceed to the wiring steps in the next step. Once you are complete
with the wiring, the Lanyard will push into the junction box when the
fixture is placed for final mounting.
Button Stop
Lanyard
Slot
Slot
Crossbar
Figure 4
Figure 5
STEP 5 - Making the Wire Connections
A. Wrap bare or green ground wire around green ground screw on the
Green Ground Screw
on the Crossbar
White wire
from outlet box
White wire from fixture
identified with the Label “N”
Black wire from
outlet box (or Red)
Black wire from fixture
identified with the label “L”
Bare, or Green
Ground wire
from outlet box
Ground wire
from Fixture
STEP 6 Install Ceiling Canopy to Crossbar-
A. Attach the Ceiling Canopy (HH) over the end of the Nipple (DD) and
secure with the Hex Nut (CC). Hand tighten until snug.
B. Thread the Mounting Ball (EE) onto the Nipple (DD) and hand
tighten until snug.
DD
EE
CC
HH
Figure 6
STEP 7 - Install Cage, Antlers and Bulbs
A. Connect side chains of the Cage (A) to loops underside of the fixture
canopy with Quick Links (GG).
B. Carefully place Antlers (C) onto the Cage (A).
C. Insert bulbs onto sockets and screw snugly into place.
Your fixture is now assembled and ready to use. Enjoy!
Figure 7
(Step 5 Continued)
crossbar, no less than 2 inches from the end of the wire. Tighten the
green ground screw.
Use standard wire connectors (not included) to make all wire
connections. Twist connectors until wires are tightly joined together.
Wrap each connection with approved electrical tape and carefully
stuff all the connected wires into outlet box.
Note: If the electrical wire is going to be cut shorter than provided
you will need to identify the "L" line wire and the "N" neutral wire
before you cut the excess wire off. One is labeled N and the other
labeled L. To do this separate the "L" line wire and the "N" neutral
wire as far as you need to. Re-label the wire near where you want to
make the cut. Be sure to mark the wire on the side of the fixture and
not on the excess wire being cut and removed.
B.
Socket
Bulb (not
supplied)
A
Side Chain
GG
Loop
C
B
Fixture Canopy