Assembly Instruction

ManualsBrandsUnion Rustic ManualsCeiling LightsLopiccolo 6 - Light Kitchen Island Linear Pendant with Antler Accents

1of3

Warnings and Cautions

Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.

These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly

recommend that a licensed, professional electrician perform the installation.

Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal.

(6)B10CandelabraBasebulbs60WMaximum

20-30minutes

Identifyandinspectallpartsbeforebeginninginstallation.Checkpackagecontentlistanddiagramsbelowtoensureallpartsare

present.Ifanypartsaremissingordamaged,donotattempttoassemble,install,oroperatethefixture.Contactcustomerserviceforreplacement

parts.

LightSource:

EstimatedAssemblyTime:

Preparation:

ToolsRequired: Flathead screwdriver, Phillips screwdriver, pliers, wire cutters, wire strippers, electrical tape, safety glasses.

Package Contents

Hardware Contents

Crossbar

Lock Washer

Hex Nut

Nipple

Mounting Ball

Ceiling

Canopy

Fixture Chain

Quick Link

Cage

Fixture Body

(Step 2 Continued)

of the Fixture Body (B) with two Quick Links (GG) as shown. Lift the

fixture and Fixture Chains (FF) up and attach the other ends of the

Fixture Chains (FF) onto the ceiling loops underside of the Ceiling

Canopy (HH) with the rest two Quick Links (GG).

Suggested rods and chain length for Ceiling height :

8’ ceiling : use 11 links of chains and 4 quick links

9’ ceiling : use 21 links of chains and 4 quick links

10’ ceiling : use 31 links of chains and 4 quick links

Supply Wires

and Ground Wire

Figure 1

Ceiling Canopy

Fixture Loop

STEP 2 - Install the Crossbar to the junction box

A. Attach the Crossbar (AA) to the Outlet Box with the head of the

Green Ground Screw facing you. Secure it with Outlet Box Screws

(not included), tighten until snug.

Figure 2

Outlet Box

Outlet Box Screw

(not included)

Green Ground

Screw

Antler

Antler A

Antler B

Antler C

STEP 1 - Install Fixture Chains

A. Adjust the Fixture Chain (FF) to your desired length by removing the

links if needed.

B. With the Fixture Chain (FF) not attached to the fixture loops on the

top of the Fixture Body (B) and the ceiling loops underside of the

Ceiling Canopy (HH), pull the supply wires and ground wire through

the Fixture Chain (FF) alternating links. After the wires are through

the Fixture Chain (FF), pull the supply wires and ground wire through

the Ceiling Canopy (HH).

C. Attach one ends of the Fixture Chains (FF) to fixture loops on top

Antler D

Assembly Instruction

Summary of content (3 pages)

PAGE 1
Assembly Instruction Tools Required: Flathead screwdriver, Phillips screwdriver, pliers, wire cutters, wire strippers, electrical tape, safety glasses. Light Source: (6) B10 Candelabra Base bulbs 60W Maximum Estimated Assembly Time: 20-30 minutes Preparation: Identify and inspect all parts before beginning installation. Check package content list and diagrams below to ensure all parts are present. If any parts are missing or damaged, do not attempt to assemble, install, or operate the fixture.
PAGE 2
STEP 3 - Install Nipple to Crossbar (Step 5 Continued) A. Thread one Hex Nut (CC) to the middle of the Nipple (DD). Place the Lock Washer (BB) over the Nipple (DD) and then thread the Nipple (DD) into the Crossbar (AA) until the Nipple (DD) is about 0.375” above the Crossbar (AA). B. Place the Ceiling Canopy (HH) over the end of the Nipple (DD) against the ceiling to determine the correct position of the Nipple (DD). Thread the Mounting Ball (EE) onto the Nipple (DD).
PAGE 3
NOTE: ALL DIMENSIONS ARE ROUNDED UP TO THE NEAREST 1/4" FINISH: EARTH BLACK 12” 71.25” OVERALL HEIGHT ( INCLUDES 48” CHAINS AND 4 QUICK LINKS ) 18.