UDWC23 Accessory Camera User’s Manual What’s in the Box Camera stand Portable video camera If any items are missing or damaged, contact our Customer Care Line immediately. Never use damaged products! AC adapter Need Help? Get answers 24/7 at our website: www.uniden.com. If You... Contact Uniden’s...
Important Safety Instructions! This manual contains important information about this product’s operation. If you are installing this product for others, you must leave this manual or a copy with the end user. When using your equipment, always follow basic safety precautions to reduce the risk of fire, electric shock and injury to persons, including the following: ► ► ► ► ► ► ► This equipment is NOT waterproof. DO NOT expose it to rain or moisture. DO NOT immerse any part of the product in water.
► to make sure that you and your parent or guardian understand these terms, conditions, and safety warnings. Allow for proper ventilation when units are in use. Do not cover the camera or receiver with any object such as a blanket. Do not place it in a drawer or in any location which would muffle the sound or interfere with the normal flow of air.
Getting Started Connecting the Power 1. Connect one end of the AC adapter Battery to the camera’s status power connector Link and the other status end to a standard Power 120 volt AC status outlet. 2. Press the Power button on the camera; the Power status light should turn on. If it doesn’t, try reconnecting the AC adapter, and make sure the power outlet isn’t controlled by a wall switch.
Learning the Buttons and Lights Button What it does POWER Turn the camera on. Press and hold to turn it off. Link Enter pairing mode. Light State Power Status light Link Status light Battery Status light What it means On The camera is on. Off The camera is off. Flashing The camera is in pairing mode. Orange Off Green The camera is connected to the receiver. The camera is in standby. The battery is charging. Red The battery is low; the camera will turn off in 3 minutes.
Camera brace Mounting screw 1. Hold the base of the mount where you want to attach it, and mark the location of the screw holes. 2. Use the included screws and anchors to attach the base to the wall or ceiling. 3. Attach the camera to the mounting screw. Tighten it a few turns, then turn it to the direction you want. 4. Tighten the camera brace up against the back of the camera to secure it into place. 5. Unlock the mounting post by turning the wingnut to the left a few turns. .
Pairing the Camera Before you can use the camera, you’ll need to “introduce” or pair it to the receiver so they can communicate. You might also perform the pairing procedure if you are having trouble with the camera. 1. Make sure the camera is powered on. 2. On the receiver, select the channel you want to pair this camera to, and put the receiver into pairing mode. (This process is slightly different on each receiver. See the manual that came with your receiver for instructions.) 3.
Additional Information Product Specifications Radio Frequency Transceiver RF Frequency 2402 Mhz ~ 2483.
Camera Specifications Low light solution 11 IR LEDs, 1 Low light sensor Low light sensitivity 1-8 lux Picture sensor OV7725 1/4’ Color CMOS Lens F3.6mm H:53 V:40 Polymer-Lithium Battery Warning ► ► ► ► ► ► ► ► CAUTION! Risk of explosion if battery is replaced by an incorrect type! This equipment contains a rechargeable polymer-lithium battery.
FCC Compliance Information Part 15 Compliance Statement This device complies with Part 15 of the FCC Rules. Operation is subjected to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with limits for a Class B digital device, pursuant to Part 15 of the FCC rules and ETSI (EN) 300328.
IC Compliance Information Radio Equipment Notice The term “IC:” before the radio certification number only signifies that Industry Canada technical specifications were met. Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. “Privacy of communications may not be ensured when using this device”.
STATEMENT OF REMEDY: In the event that the product does not conform to this warranty at any time while this warranty is in effect, warrantor will either, at its option, repair or replace the defective unit & return it to you without charge for parts, service, or any other cost (except shipping & handling) incurred by warrantor or its representatives in connection with the performance of this warranty. Warrantor, at its option, may replace the unit with a new or refurbished unit.
