User's Manual
Table Of Contents
- Copyright © 2020 San Jose Technology, Inc. All Rig
- This document contains information that is the pr
- 2
- Document Amendments
- Specification
- Package Contents
- Front View
- SJ-205HAB Quick START/Setting Guide
- STEP 1: APN Identification. Ensure APN Name, APN u
- STEP 2: Send SMS command to device (Check the IMEI
- STEP 3: Send SMS command to device to set up APN:
- default: #username,0000,3,internet,,*(if empty, le
- STEP 4: Send SMS command to point to TCP server: #
- STEP 5: Send SMS command to device to report via T
- SETP 6: Set RTC Time：#username,0000,setrtc,1610121
- 10
- Command Setup for SJ-205HAB
- Change User Name
- Change Password
- Request IMEI Number
- Set up APN for mobile network Service
- Set up URL
- Set up TCP ACK function
- Set up Phone Book List
- Set up Location Auto Report Mode
- Set up Answer Call Mode
- Set up Mandatory Polling report
- Set up Route for Data Transmission
- Get Pairing Information
- Set up Auto Reboot Time
- Set up TCP/UDP Server Address
- Set up Turbo Link Mode
- Set up Command By GPRS
- Set up Device Position
- Set up RTC time
- Set up Tamper Function
- Set up Vibration Detection Function
- Set up Alarm OFF
- Disable the beep sound when alarm event is trigge
- Set up RF power of Home unit
- Set up AES 128 Encryption
- Set up FOTA (Over-the-Air Technology)
- Set up paired with the bracelet (NB5)
- Set up unpaired with the bracelet (NB5)
- IDRST (Clear all of the idpair at the same time)
- RF Command
- Erase the Backup Data(Clear the flash memory)
- Setup buzzing when receiving RF signal
- Setup RFall feature
- Set up Low Power reminder
- Appendix 1: Tracker Event List
- 47
- 48
- 49
- In order to expedite the SANAV repair process, cus
- 1.Neglect, misuse, or abuse, such as incorrect testi
- 2.Placement of unit in extreme environments beyond t
- 3.Subjugation of unit to disassembling, soldering, a
- 4.Any incidental or consequential losses or damages
- 5.Disaster, accidents, use of any inauthentic substi
- 50
- 空白页面
Set up Auto Reboot Time
User can use the following commands below to set the device’s auto reboot for clean up the system status
regularly.
Setup Format: #「USERNAME」,「Password」,「Function Mode」,「Intervals (30 min.) 」*
Command: #USERNAME,0000,rst,48 *
SMS/ COTA Command
Description
#
Start sign.
USERNAME
Default ID of the device.
If you have changed the user name, please use the updated one.
0000
Default password.
If you have changed the password, please use the updated one.
rst
“rst” defines the auto reboot mode
48
30 minutes as a unit. The range is 0 to 99. 0 is disable.
Example: 48 means 24hr reboot once
*
End sign.
Table25: Auto Reboot Time Setup Format Description
Situation
Message Reply
Setup Succeeds
[username] + Auto Reset is defined.
[username] + Auto Reset is disabled.
Incorrect username or
password,
Incorrect command format
[username] + command error
Table26: Auto Reboot Time Setup Response Description
11F., No.2, Sec. 4, Jhongyang Rd., Tucheng Dist., New Taipei City 236, Taiwan (R.O.C.)
Tel: 886-2-22694456｜Fax: 886-2-22694451｜service@unictron.com
26
w
w
w
w
w
w
.u
.
n
sa
ic
n
tr
a
o
v
n
.
.
c
c
o
o
m
m
© Unictron Technologies Corp.
All specifications subject to change without notice.