User's Manual
Table Of Contents
- Copyright © 2020 San Jose Technology, Inc. All Rig
- This document contains information that is the pr
- 2
- Document Amendments
- Specification
- Package Contents
- Front View
- SJ-205HAB Quick START/Setting Guide
- STEP 1: APN Identification. Ensure APN Name, APN u
- STEP 2: Send SMS command to device (Check the IMEI
- STEP 3: Send SMS command to device to set up APN:
- default: #username,0000,3,internet,,*(if empty, le
- STEP 4: Send SMS command to point to TCP server: #
- STEP 5: Send SMS command to device to report via T
- SETP 6: Set RTC Time：#username,0000,setrtc,1610121
- 10
- Command Setup for SJ-205HAB
- Change User Name
- Change Password
- Request IMEI Number
- Set up APN for mobile network Service
- Set up URL
- Set up TCP ACK function
- Set up Phone Book List
- Set up Location Auto Report Mode
- Set up Answer Call Mode
- Set up Mandatory Polling report
- Set up Route for Data Transmission
- Get Pairing Information
- Set up Auto Reboot Time
- Set up TCP/UDP Server Address
- Set up Turbo Link Mode
- Set up Command By GPRS
- Set up Device Position
- Set up RTC time
- Set up Tamper Function
- Set up Vibration Detection Function
- Set up Alarm OFF
- Disable the beep sound when alarm event is trigge
- Set up RF power of Home unit
- Set up AES 128 Encryption
- Set up FOTA (Over-the-Air Technology)
- Set up paired with the bracelet (NB5)
- Set up unpaired with the bracelet (NB5)
- IDRST (Clear all of the idpair at the same time)
- RF Command
- Erase the Backup Data(Clear the flash memory)
- Setup buzzing when receiving RF signal
- Setup RFall feature
- Set up Low Power reminder
- Appendix 1: Tracker Event List
- 47
- 48
- 49
- In order to expedite the SANAV repair process, cus
- 1.Neglect, misuse, or abuse, such as incorrect testi
- 2.Placement of unit in extreme environments beyond t
- 3.Subjugation of unit to disassembling, soldering, a
- 4.Any incidental or consequential losses or damages
- 5.Disaster, accidents, use of any inauthentic substi
- 50
- 空白页面
Command Setup for SJ-205HAB
SJ-205HAB currently provides SMS command and COTA (TCP) command for remote setup. User can setup the
SJ-205HAB by following the instructions shown in following chapters via SMS/COTA. Key the specific SMS
message in your cellular phone and send it to the SIM number of SJ-205HAB. The setup messages are showed
in the following sections.
1: The default setting:
Default ID is “USERNAME”. Please read chapter Change User Name to desired ID.
Default password is “0000”. Please read chapter Change Password to change the password.
There is no number in the default contact. Please read chapter Set up Phone Book List to add the number.
Default setting of Retrospective Location Mode is deactivated. Please read chapter Set up Retrospective
Location Mode by Time to setup the regular Retrospective Location Mode.
Default setting of APN is only suitable for mobile network. Please read chapter Set up APN for MOBILE
NETWORK Service to change the APN.
Default setting of URL is http://www.sanavtw.com/uploadM1.php. Please read chapter Set up URL to
change the URL for http server setup.
Before doing any setup, please ensure the device is connected with the GSM network. The GSM LED must light
on. And please note the device is not in SOS/Panic mode.
2: Please note that all the characters which include #, * and comma (,) should be HALFWIDTH form.
3: Please be aware of the upper (capital)/lower cases when entering the SMS command.
4: While entering any SMS command, note that NO SPACE is allowed between the characters, comma and
signs in the SMS.
5: Any setup command must be started with a “#” sign and ended up with a “*” sign.
6: The comma (,) can be abbreviated if no further setup required for the command besides Set up APN for LTE
Service. Please refer to the examples of Set up Retrospective Location Mode.
7: Add or not add the “+ “sign in front of the cellular phone number(s) are both acceptable, while the”+” sign
should precede the international call prefixes. The specified international call prefix is required if “+ “sign is not
added.
8: The device will update setting Only when the password, USERNAME and setup command are all correct.
If the command is not valid, a failure report is going to be sent to the user’s cell phone.
9: Some PREPAID PHONE CARD SIM modules do not enable or even support MOBILE NETWORK service. Please
consult with GSM carrier for further information.
11F., No.2, Sec. 4, Jhongyang Rd., Tucheng Dist., New Taipei City 236, Taiwan (R.O.C.)
Tel: 886-2-22694456｜Fax: 886-2-22694451｜service@unictron.com
11
w
w
w
w
w
w
.u
.
n
sa
ic
n
tr
a
o
v
n
.
.
c
c
o
o
m
m
© Unictron Technologies Corp.
All specifications subject to change without notice.