Tracking Solutions Embedded Antenna design GPS&Wireless solutions Provider Part Number: NB-5 Doc Type : User Manual Doc Id: WI-RD-E-054 Reversion : V1.0 Copyright © 2020 San Jose Technology, Inc. All Rights Reserved. This document contains information that is the property of SANAV.
Specifications ................................................................................................................ 3 NB5 Function Overview ........................................................................................... 4 NB5 Tracker Installation ........................................................................................ 8 Cutting Tools ................................................................................................................
GSM GSM Module: GSM Frequency: 3G Transmission: uBlox SARA U201 3G: 800/ 850/ 900/ 1900/ 2100MHz GSM: 850 / 900/ 1800/ 1900MHz Power class 3 (24 dBm) for WCDMA/HSDPA/HSUPA mode GPS GPS Module: u-blox G8030 support NMEA0183 Sensitivity: -164 dBm Channels/ Frequency: 72 Channels/ GPS/QZSS/GLONASS TTFT(Hot/Warm/Cold): Position Accuracy: © Unictron Technologies Corp. All specifications subject to change without notice. Specifications Cold/Warm <26 seconds Hot <1 second 2.
IP68 NB5 Function Overview 1. Basic Function Introduction NB5 is multi-functional electronic monitoring ankle bracelet with GPS/3G/RF monitoring technology. With electronic monitoring technology, you have ability to reliability track user’s location. NB5 utilizes GPS and 3G services to upload the RMC sentences containing latitude, longitude, date and time to assigned monitoring center. It is specially designed for the intensive tracking applications, such as offender tracking or life security.
Charge 3 hours to provide above 30-hour operation (each report/1 minutes, no general alarm) 3. Front View GSM GPS CH STATUS © Unictron Technologies Corp. All specifications subject to change without notice. LED (from left to right): 1. GPS Positioning LED (Blue): While the device gets GPS fixed, the GPS light will stay on. 2. GSM LED (Red): While the device gets GSM fixed or in normal operation, the GSM light will flash every 3 seconds.
CH charger LED will be off. 5. Charge Socket (Red circle): Please make sure to use San Jose original charger and charging pack to protect your equipment. © Unictron Technologies Corp. All specifications subject to change without notice. charged, the CH LED will stay on. Unplug the charger when the device is fully charged. In this situation, 11F., No.2, Sec. 4, Jhongyang Rd., Tucheng Dist., New Taipei City 236, Taiwan (R.O.C.) Tel: 886-2-22694456｜Fax: 886-2-22694451｜service@unictron.com 6 www.unictron.
© Unictron Technologies Corp. All specifications subject to change without notice. 4. Back Cover 5. Wall Charger 11F., No.2, Sec. 4, Jhongyang Rd., Tucheng Dist., New Taipei City 236, Taiwan (R.O.C.) Tel: 886-2-22694456｜Fax: 886-2-22694451｜service@unictron.com 7 www.unictron.com www.sanav.
Note: The device must be fully charged prior to installation. Remember to wear a pair of socks for comfortable attaching. 1. Circle the user’s leg with strap and installation height of NB5 will be 8-10cm from an outer ankle. 2. © Unictron Technologies Corp. All specifications subject to change without notice.
Please note that the cutting line should be on the groove between two scales for easy cutting and wearing purpose. 6. While cutting the strap by using the © Unictron Technologies Corp. All specifications subject to change without notice. 5. dedicated strap, it should proceed with 3 stages cutting procedures. Keep cutter and strap at 90-degree angle to make sure that the cutting edge should be flat. (1) 1ST stage: Cut slowly from strap edge to 2/5 of strap width (as marked “1” of right picture).
Cut procedures are completed. 8. Put up the Jelly cover at the end of © Unictron Technologies Corp. All specifications subject to change without notice. 7. strap. Please refer to NB5 Jelly cover assembly SOP. 9. Fix the strap clip at the end of strap. 10. Insert the strap with strap clip into the socket chamber at rear cover right side. Press the strap deeply into the chamber. Make sure the strap can not be pull-off from the strap chamber. Snap Snap 11F., No.2, Sec. 4, Jhongyang Rd.
Activated. Start tracking. 12. While using wall charger, aim the © Unictron Technologies Corp. All specifications subject to change without notice. 11. charger connector (female) to NB5 charge socket (male), push till the end to lock the device. Unplug the wall charger in correct direction to avoid from charge socket or charger malfunction. 13. Connected and charged. 11F., No.2, Sec. 4, Jhongyang Rd., Tucheng Dist., New Taipei City 236, Taiwan (R.O.C.
1. Make sure that the front side of the cutting tool faces to you and that the strap’s entrance direction. The spare blades are restored in the red rectangle. 2. © Unictron Technologies Corp. All specifications subject to change without notice. Cutting Tools Check that the blade is right on the block that should be cut. 11F., No.2, Sec. 4, Jhongyang Rd., Tucheng Dist., New Taipei City 236, Taiwan (R.O.C.) Tel: 886-2-22694456｜Fax: 886-2-22694451｜service@unictron.com 12 www.unictron.com www.sanav.
After making sure the location is right, push the top of cutting tool to cut the strap 4. Exchange the blade if needed. © Unictron Technologies Corp. All specifications subject to change without notice. 3. Release the screw ant then remove the blade. Note that releasing completely the screw is not necessary. Notice the direction of the blade since we need to install the spare blade on the same direction later. 11F., No.2, Sec. 4, Jhongyang Rd., Tucheng Dist., New Taipei City 236, Taiwan (R.O.C.
Install the blade. Please make sure the edge of the blade is inside the white area on the cutting tool. Push the top of cutting tools to the bottom so that the blade is back to the right place and screw it up. © Unictron Technologies Corp. All specifications subject to change without notice. 5. 11F., No.2, Sec. 4, Jhongyang Rd., Tucheng Dist., New Taipei City 236, Taiwan (R.O.C.) Tel: 886-2-22694456｜Fax: 886-2-22694451｜service@unictron.com 14 www.unictron.com www.sanav.
SMS Command setting 1. Any setup command must be started with a “#” sign and ended up with a “*” sign. Please note that all the characters which include “#”, “*” and comma (,) should be HALFWIDTH form. 2. Please be aware of the upper (capital)/lower cases when entering the SMS command. 3. While entering any SMS command, note that NO SPACE is allowed between the characters, comma and signs in the SMS. 4.
Once the events such as strap violation and device tamper are triggered, NB5 will send the reports with the alarm message followed by the beep sound and vibration. This command is used to deactivate the alarm status, and then the device will be detecting the events. Setup Format：#, , * Example：#username,0000,alarmoff* (1) Turn on ‘buzz sound when alarming’ function (Function Code 19). © Unictron Technologies Corp. All specifications subject to change without notice.
Set up Username Generally, SMS command execution needs correct user name (I.D) with password, or it will remain the same setting. The SMS command default user name is “username”. It can be changed by following the command format. For example, entering the SMS command as the following allows user to change the user name from “username” to a new user name “abc”. Only enter new command with new user name after it has been changed. © Unictron Technologies Corp.
Generally, SMS command execution needs correct user name with password, or it will remain the same setting. The SMS command default password is “0000”. It can be changed by following the command format. For example, entering the SMS command as the following allows user to change the password from “0000” to a new password “1111”. Only enter command with new password will be valid for setting change after it has been changed.
Security Phone Number allows limited administrators to manage and change the settings of the bracelet. When the Security Phone Number is set, even the User Name and Password are correct, if the setup phone number is not matched, the setup or any change will be invalid. Please be careful when setting up Security Phone Number. Security Phone Number also is the number that is used when the router is set as HTTP/SMS, TCP/SMS or SMS mode.
End sign. © Unictron Technologies Corp. All specifications subject to change without notice. * Table: Security Phone Number Setup Format Description Situation Message Reply Setup Succeeds [username] + Device phone book is updated. Table: Security Phone Number Setup Response Description STEP 3: Set up HA ID The bracelet (HA) ID is set for identification. The ID number ranges from 1 to 9999. The ID will be shown in the reports. E.g. imei=356496041252545&rmc=$GNRMC,020733.00,A,2457.80794,N,12125.
This command is for the bracelet with RF capability. Once the RF Detect function is turned on, the device can communicate with the Home Unit. This command can be used for site survey when installing Home Unit. When RF test mode (the 2nd parameter) is turned on, the bracelet will beep when it receives the RF signal from Home Unit.
The ankle bracelet RF transmit power can be set for Home Unit curfew range adjustment. There are totally 8 levels of RF transmit power that can be set. The stronger the RF transmit power is, the wider the curfew range would be. We always adjust the level of RF transmit power for both the bracelet and Home Unit. RF channel defines that all the equipments including NB5 (bracelet), HU3 (Home Unit) should use the same channel to communicate each other.
Access Point Name (APN) is a protocol that typically allows a user's device to access the internet using the mobile phone network. It is a network identifier used by a mobile device when connecting to a GSM carrier. The carrier will then examine this identifier to determine what type of network connection should be created. © Unictron Technologies Corp. All specifications subject to change without notice.
Message Reply Setup Succeeds [username] +, Device GPRS APN is updated. Table: APN Setup Response Description STEP 7: Set up URL and TCP/UDP IP Address Set up URL This SMS command is for setting up a specified URL (Uniform Resource Locator) or IP address of HTTP protocol server where the bracelet will transmit GPS (GPRMC) positioning data to for real time GPS tracking as route of the device is set as HTTP mode. © Unictron Technologies Corp. All specifications subject to change without notice.
This SMS command is for setting up a specified TCP or UDP protocol based server where the bracelet will transmit GPS (GPRMC) positioning data for real time GPS tracking as route of the device is set as TCP or UDP mode. E.g. Use function code 18 to setup the URL as the following command to configure URL for TCP or UDP. Setup Format：#,,,：* Example：#username,0000,18,202.39.31.127:13337* SMS Text Description # Start sign.
This SMS command set up the route that determine in which protocol the device ends up transmitting GPS (GPRMC) positioning data. Please confirm the back-end server protocol type and corresponded URL or IP address with port number before setup. There are 3 main protocols available: 1. HTTP: Hypertext Transfer Protocol. An internet browser based server protocol that usually has a specified URL (Uniform Resource Locator). 2.
Message Reply [username] +, Device is switching to HTTP mode. [username] +, Device TCP is updated. Setup Succeeds [username] +, Device is switching to SMS mode. Table: Data Transmission Route Setup Response Description STEP 9: Set up Auto Report (Optional) Auto Report setup can enable the bracelet report GPS data automatically during a period of time. Use this command to set up the frequency of Auto Report. The bracelet can report according to interval. If you © Unictron Technologies Corp.
Message Reply Setup Succeeds [username] + Setup OK. Device Auto Report setting is updated. Setup Fail [username] + Auto Report setting Setup Fail! Incorrect password [username] + Password setup Fail! Incorrect username or [username] + command error command format Table: Auto Report Setup Response Description Step 10: Request IMEI Number IMEI stands for International Mobile Equipment Identification, a unique number for identifying mobile devices © Unictron Technologies Corp.
1 2 357520074257524, $GNRMC,081219.00,A,2457.80821,N,12125.53897,E,0.054,,160720,,,A*6C, 3 4 5 6 7 8 9 AUTO, I0200, , , , 9970, M16, 1 13 466 , 4 1, 15 16 24A5 13E16E , 9, Item Name 1 IMEI number 10 11 12 3782mV, 45, 2.40, 17 18 19 20 21 22 23 24 25 26 27 36, FFFF, 45, 10613, 27, 14, FFFF, 29, 10613, 25, 10 © Unictron Technologies Corp. All specifications subject to change without notice.
GSM Cell ID MNC Mobile Network Code. The range is 0-999 (1 to 3digits). 15 GSM Cell ID LAC Location Area Code, The range is 0x0-0xFFFF (2 octets) Cell identity. 16 GSM Cell ID The range is: o 2G cell: range 0x0-0xFFFF (2 octets) o 3G cell: range 0x0-0xFFFFFFF (28 bits) Cell identity. 16 GSM Cell ID The range is: o 2G cell: range 0x0-0xFFFF (2 octets) o 3G cell: range 0x0-0xFFFFFFF (28 bits) © Unictron Technologies Corp. All specifications subject to change without notice.
• 91: -25 dBm Energy per Chip/Noise ratio expressed in dB levels: 27 ecn0_lev • 0: less than -24 dB • 1..48: from -24 dB to 0.5 dB with 0.5 dB steps • 49: 0 dB Appendix 2: Tracker Event List This table shows the different events/ messages sent from the device. Basically, there are more than 10 different situations that trigger the device to respond its position and tracker © Unictron Technologies Corp. All specifications subject to change without notice. • 1..
(1) Any event marks with letter “B” (Bauto…..) represents data which was not able to send to assigned route immediately due to priority or mobile network service is not available. The data will be sent after the issues are cleared. (2) The event marks with letter“L”(LAUTO) represents power saving mode for data transmission. "LAUTO" represents a specific number of AUTO reports. The equipment will send reports at once as a group when it has logged a fixed number of reports in the memory.
This command is to erase the reports restored in the flash memory before. Once the GSM signal is weak or other reasons that cause that the device is not able to send reports to the server, the reports will be restored in the flash memory and re-sent later. In some case, you might want to erase those reports immediately, and then you can use this command. Please make sure that those reports in flash won’t be needed anymore before you use it.
Use this SMS command to restart the device remotely. This command allow user to restart the device immediately or in schedule. Setup format: #, , , * Command: #username,0000,rst,9* Command: #username,0000,rst,now* SMS Text Description # Start sign. username Default user name of the device. If you have changed the username, please use the updated one. Default password. If you have changed the password, please use the updated one.
This setting defines the behavior when the device restarts. We can choose which opponent will be restarted such as MCU, GSM and GPS. Setup format: #, , , , * Command: #username,0000,rst,cfg,7* Command: #username,0000,rst,cfg,6* SMS Text Description # Start sign. username Default user name of the device. If you have changed the username, please use the updated one. Default password.
This feature is for acquire the device’ position immediately. Once the device has received the POLL command, the POLL message will be sent to the server depending on the route you’ve set. The POLL message will be shown in the “Event” field of the report. Setup Format：#, , * Example：#username,0000,10* SMS Text Description # Start sign. username Default ID of BRACELET. © Unictron Technologies Corp. All specifications subject to change without notice.
FRB feature is for detecting the strap violation. The default setting of “FBR Tamper” detected time is 10 seconds due to fiber characteristic. When the feature is turned on, if the strap is cut, the alarm will be triggered and the device will send the ST reports to indicate the strap violation. The ST state will be shown in the state field of report. The interval of ST report depends on the setting. There may be a buzzing sound or vibration if the buzzer and vibrator are turned on.
FRB feature is for detecting the Tamper violation. When the feature is turned on, if the cover of the bracelet is opened, the alarm will be triggered immediately and the device will send the DT reports to indicate the strap violation. The DT state will be shown in the state field of report. The interval of DT report depends on the setting. There may be a buzzing sound or vibration if the buzzer and vibrator are turned on.
When the Alarm events (such as ST, DT, Geo-fence event) are triggered, the device will beep and vibrate for notice as well as send the reports. This command is to toggling the beep sound and vibration respectively and configuring the interval of notice. This command only affects the beep sound and vibration when the Alarm events are triggered.
Message Reply Buzzer setup succeed [username] +, setup OK. Device buzzer is turned off. / on. Vibrator setup succeed [username] +, vibration motor is disabled. / enabled. Buzzer and Vibrator setup scceed [username] +, setup OK. Buzzer & vibrator setting are updated.
This mode has two part of feature. In Power Saving Mode 0, the battery life can be saved by stopping GPS output temporarily while the device isn’t reporting. This is the default setting. Set to 0 to enable it such like this command: #username,0000,combo,0*. In Power Saving Mode 1, power save mode will be disabled and the GPS is always on. If the GPS signals are often poor in your environment, to use this mode is recommended.
Set to 1 to enable it such like this command: #username,0000,aes,1*. Setup Format: #, , , * Command: #username,0000,aes,1* SMS Text Description # Start sign. username Default user name of the device. If you have changed the username, please use the updated one. Default password. If you have changed the password, please use the updated one. 0000 AES Encryption Mode * © Unictron Technologies Corp.
Set to 1 to enable it such like this command: #username,0000,tcpack,1*. Setup Format: #, , , * Command: #username,0000,tcpack,1* SMS Text Description # Start sign. username Default user name of the device. If you have changed the username, please use the updated one. Default password. If you have changed the password, please use the updated one. 0000 TCPACK Function Mode * © Unictron Technologies Corp.
The user can set the SMS/COTA command to alert user if the battery voltage is low or automatically shut down system when the battery voltage reaches a certain threshold. Setup Format: #, ,, ,< Voltage Value 2>* Command: #UserName,0000,LP,3650,50* SMS/ COTA Command Description # Start sign. UserName Default ID of the device. If you have changed the user name, please use the updated one. Default password.
Use this command to switch the display GSM Cell Information in the data of report. Setup Format: #, ,, * Command: # UserName,0000,cellid,1* SMS/ COTA Command Description # Start sign. UserName Default ID of the device. If you have changed the user name, please use the updated one. 0000 © Unictron Technologies Corp. All specifications subject to change without notice. GSM Cell Information Setting Default password.
Use this command to upgrade firmware from a file on http server. Setup Format: #, ,, * Command: # UserName,0000,fota,Http://220.128.123.1:8000/NB5-F5359-0609201617-VA1.0.3-OTA(00383390).txt* SMS/ COTA Command Description # Start sign. UserName Default ID of the device. If you have changed the user name, please use the updated one. 0000 © Unictron Technologies Corp. All specifications subject to change without notice.
FCC Statement This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
