ENDAT-K1001 USERS MANUAL UNICORN COMPUTER CORP. ENDAT-K1001 User’s Manual For ENDAT-K1001 PCB ver.
ENDAT-K1001 USERS MANUAL UNICORN COMPUTER CORP. Copyright Notice The content of this manual has been checked for accuracy. The manufacturer assumes no responsibility for any inaccuracies that may be contained in this manual. The manufacturer reserves the right to make improvements or modification to this document and/or the product at any time without prior notice.
ENDAT-K1001 USERS MANUAL UNICORN COMPUTER CORP. Specification: Model System Chipset ENDAT-K1001 AMD RS780E+SB710 (TDP 15+4.5 Watt) Support AMD SEMPRON / ATHLON / ATHLON X2 / CPU Supporting PHENOM X3 / PHENOM X4 AM2/AM2+/AM3 socket CPU - 2 x SODIMM sockets Memory - Support DDR2-800/667/533/400 up to 8GB Ethernet 2 x REALTEK RTL8111B Gigabit Ethernet Controllers - Integrated ATI Radeon™ HD 3200 GPU - Support onboard 128MB Side-port Memory (optional) - Support Microsoft® DirectX 10, Shader Model 4.
ENDAT-K1001 USERS MANUAL UNICORN COMPUTER CORP. TABLE OF CONTENTS CHAPTER 1. INTRODUCTION....................................................... 6 1-1. 1-2. 1-3. 1-4. FEATURES .............................................................................................. 7 UNPACKING ............................................................................................ 8 ELECTROSTATIC DISCHARGE PRECAUTIONS ................................... 8 MOTHERBOARD LAYOUT .......................................
ENDAT-K1001 USERS MANUAL UNICORN COMPUTER CORP. CHPATER 4. VGA, LCD AND DRIVERS...................................... 40 4-1. VGA FEATURE....................................................................................... 40 4-2. DRIVER UTILITY INSTALLATION GUIDE.............................................. 41 APPENDIX A: FLASH MEMORY UTILITY ................................... 42 APPENDIX B: LIMITED WARRANTY ..........................................
ENDAT-K1001 USERS MANUAL UNICORN COMPUTER CORP. Chapter 1. Introduction In order to optimize the overall system and graphics performance of embedded system in diverse application, ENDAT-K1001 system board provides the ultimate solution by integrating with ATI Radeon™ HD 3200 DirectX® 10 GFX engine in AMD RS780E system chipset. The ATI Radeon™ HD 3200 (M72-based) graphics core employs a unified shader architecture to deliver optimal 3D performance across the whole spectrum of 3D applications.
ENDAT-K1001 USERS MANUAL UNICORN COMPUTER CORP. 1-1. Features Basic Feature: High performance CPU and GFX with cost effective platform. Support AMD AM2/AM2+/AM3 socket CPU. Two DDR2 SODIMM sockets support DDR2-400/533/667/800 up to 8GB system memory. ATI Radeon™ HD 3200 DirectX® 10 GFX engine with 128MB local memory (optional feature) and UMA mode (shares system memory up to 1GB) 7.
ENDAT-K1001 USERS MANUAL UNICORN COMPUTER CORP. 1-2. Unpacking The motherboard comes securely packaged in a sturdy cardboard shipping carton. In addition to the User's Manual, the motherboard package includes the following items: ENDAT-K1001 System Board SATA Cables LCD cable (Optional) CD with Driver utilities for on-board VGA and LAN adapter If any of these items are missing or damage, please contact the dealer from whom you purchase the motherboard.
ENDAT-K1001 USERS MANUAL UNICORN COMPUTER CORP. 1-4. MOTHERBOARD LAYOUT.
ENDAT-K1001 USERS MANUAL UNICORN COMPUTER CORP. Chapter 2. Setting up the Motherboard 2-1.
ENDAT-K1001 USERS MANUAL UNICORN COMPUTER CORP. Box Headers, Pin Headers Overview: Function PS/2 KB/MS Header External PS/2 Device Header (KB) Connectors KBMS1 JKB1 COM-A1 (COM1) COM1 / 2 Box Header COM-A2 (COM2) USB Ports Header JUSB1, JUSB2 AUDIO Headers JAUD1 SPDIF Header SPDIF1 SMBus Header SMB1 Header for Case Panel JP1 Digital I/O Header GPIO1 Reserved Power for LCD (+3.
ENDAT-K1001 USERS MANUAL UNICORN COMPUTER CORP. Part 1: Onboard Jumpers JBAT1: CMOS Data Clear (1x3, 2.0mm) Pin 1-2 * Normal Pin 2-3 Close for clear CMOS LCDPWR1: LCD Voltage Select (2x3, 2.0mm) LCDPWR1 1-2* 3-4 5-6 12 Voltage +3.
ENDAT-K1001 USERS MANUAL UNICORN COMPUTER CORP. I-PWR1: Inverter ON/OFF Level Select (2x3 with 2.0mm) I-PWR1: LCD Backlight Voltage Select (2x3 with 2.0mm) Inverter ON/OFF Level Select I-PWR1 1-3 3-5 Voltage +3.3V* +5V LCD Backlight Voltage Select I-PWR1 2-4 4-6 Voltage +12V* +5V GPIO2: LCD Brightness Select (2x4 with 2.0mm) Pin No. 1-2 3-4 5-6 1-2, 3-4 1-2, 5-6 3-4, 5-6 Close All Open all 7-8 Voltage (V) +2.5V +1.70V +1.10V +1.25V +0.85V +0.72V +0.63V +5.
ENDAT-K1001 USERS MANUAL UNICORN COMPUTER CORP. KBPWR1: Keyboard Power Select I-PWR1 1-2 2-3 Voltage +5V Standby * +5V Part 2: Onboard Connectors and Headers KBMS1: PS/2 Keyboard / Mouse Header (2x5 with 2.54mm) Pin No. 1 3 5 7 9 Signal (KB) KB Data KEY GND +5V(DC) KB_CLK Pin No.
ENDAT-K1001 USERS MANUAL UNICORN COMPUTER CORP. JKB1: External PS/2 Device Header (1x7 with 2.0mm) Pin No. 1 3 5 7 Signal (KB) KB Data Out KB Clk Out Key GND Pin No. 2 4 6 Signal (MS) KB Data In KB Clk In +5V(DC) COM-A1 (COM1) / COM-B1 (COM2): COM port Box Headers (2x5 with 2.0mm) Pin No. Function Pin No. Function 1 DCD 6 DSR 2 RXD 7 RTS 3 TXD 8 CTS 4 DTR 9 RI 5 GND 10 N.C.
ENDAT-K1001 USERS MANUAL UNICORN COMPUTER CORP. JUSB1, JUSB2: Pin Header for USB port (2x5 with 2.54mm) Pin No. 1 3 5 7 9 Function USB_VCC USBD4/6USBD4/6+ USB_GND KEY Pin No.
ENDAT-K1001 USERS MANUAL UNICORN COMPUTER CORP. JAUD1: AUDIO Headers for Front panel (2x5 with 2.54mm) Pin No. 1 3 5 7 9 Function MIC2-L MIC2-R LINE2-R Front Panel Detect LINE2-L Pin No. 2 4 6 8 10 Function GND_AUD NA MIC2-Detect NA LINE2-Detece SMB1: SM Bus Pin Header Connector (1x4 with 2.0mm) Pin No. 1 2 3 4 17 Function SMBCK SMBDT +3.
ENDAT-K1001 USERS MANUAL UNICORN COMPUTER CORP. GPIO1: DIGITAL I/O Pin Header Connector (2x6 with 2.0mm) Pin Pin Function Function No. No. 1 +5V 2 +3.3V 3 DIO-P30 4 DIO-P31 5 DIO-P32 6 DIO-P33 7 DIO-P34 8 DIO-P35 9 DIO-P36 * 10 DIO-P37 11 GND 12 GND Notice: The DIO-P36 (pin-9 of GPIO1) is an alternate pin of chipsets. It’ll output a low frequency clock till the BIOS finished the boot operation. SPDIF1: SPDIF Header (1 x 5 with 2.0mm) Pin No. 1 2 3 4 5 18 Signal (KB) +5V N.
ENDAT-K1001 USERS MANUAL UNICORN COMPUTER CORP. LCDBK1: Inverter Header (2x3 with 2.0mm) Pin No. 1 3 5 Function VBL INV-BRT GND Pin Function No. 2 VBL 4 BKL ON/OFF 6 GND Notice1: The pin-3 of LCDBK1 voltage will change by GPIO2 or S/W control Notice2: The pin-4 of LCDBK1 voltage will change by I-PWR1 (pin-1, 3, 5) AUXPWR1: Reserved Power for LCD (1x2 with 2.0mm) AUXPWR1 Pin 1, 2 19 Voltage +3.
ENDAT-K1001 USERS MANUAL UNICORN COMPUTER CORP. LVDS1: Dual Channel LVDS (1.25mm) Pin No. 1 3 5 7 9 11 13 15 17 19 21 23 25 27 29 31 33 35 37 39 Signal VBL (+12V) GND DISP.ON/OFF LCD Power GND TxO0+ TxO1+ TxO2+ TxO3+ TxOC+ GND TxE0+ TxE1+ TxE2+ TxE3+ TxEC+ LCD Power GND GND VBL (+12V) Pin No.
ENDAT-K1001 USERS MANUAL UNICORN COMPUTER CORP. AT-ON1: AT Power Mode (1x2 with 2.0mm) AT-ON1 Open Close Mode ATX mode AT mode ATXPWR: ATX Power connector 3.3V –12V GND PS ON GND GND GND –5V +5V +5V 11 12 13 14 15 16 17 18 19 20 1 2 3 4 5 6 7 8 9 10 3.3V 3.3V GND +5V GND +5V GND POWER OK 5V SB +12V DC-IN1: DC Input connector (1x2 with 3.96mm) 1 +V 2 GND HDDPWR1: DC Output connector (1x4 with 3.
ENDAT-K1001 USERS MANUAL UNICORN COMPUTER CORP. 2-2. Installing Memory The ENDAT-K1001 offers two 200pin DDR2 SODIMM sockets supporting up to 8GB of memory. The speed of DDR memory can be DDR400, DDR533, DDR667 or DDR800. 2-3. Graphic Memory The ENDAT-K1001 integrated ATI Radeon™ HD 3200 DirectX® 10 GFX engine with 128MB DDR2 local frame buffer memory (Side Port ; optional feature) and UMA mode (shares system memory up to 1GB).
ENDAT-K1001 USERS MANUAL UNICORN COMPUTER CORP. Sample code for watch dog timer (using TurboC/C++ 3.0): #include #include #include
ENDAT-K1001 USERS MANUAL UNICORN COMPUTER CORP. 2-5. Digital I/O 1) Pin out of digital I/O header (GPIO1): Pin No. Function Pin No. Function 1 +5V 2 +3.3V 3 DIO-P30 4 DIO-P31 5 DIO-P32 6 DIO-P33 7 DIO-P34 8 DIO-P35 9 DIO-P36 * 10 DIO-P37 11 GND 12 GND Notice: The DIO-P36 (pin-9 of GPIO1) is an alternate pin of chipsets. It’ll output a low frequency clock till the BIOS finished the boot operation.
ENDAT-K1001 USERS MANUAL UNICORN COMPUTER CORP. 2-6. LCD Backlight ON/OFF Control 1) Inverter Power/ON/OFF Signal level select: I-PWR1 (Pin2, 4, 6): LCD Backlight Voltage Select (2x3 with 2.0mm) Voltage +5V +12V * I-PWR1 4-6 2-4 I-PWR1 (Pin1, 3, 5): Inverter ON/OFF Level Select (2x3 with 2.0mm) Voltage +3.3V * +5V I-PWR1 1-3 3-5 2) Backlight ON/OFF Control port address: This is alternate function with VBIOS (VESA) to offering an easy way to control the LCD backlight ON and OFF as need.
ENDAT-K1001 USERS MANUAL UNICORN COMPUTER CORP. 2-7.LCD Brightness Control 1) Inverter Brightness Digital level select: LCDBK1: Inverter Header (2x3 with 2.0mm) Pin No. Function Pin No. Function VBL VBL 1 2 INV-BRT BKL ON/OFF 3 4 GND GND 5 6 2) Brightness Control port address: This is alternate function with VBIOS (VESA) to offering an easy way to control the LCD backlight ON and OFF as need. Please follow the instructions of below for more detail in operation.
ENDAT-K1001 USERS MANUAL UNICORN COMPUTER CORP. Chapter 3. AMI BIOS SETUP BIOS Setup Utility Use the BIOS CMOS setup program to modify the system parameters to reflect the environment installed in your system and to customize the system as desired. Press the key to enter into the BIOS CMOS setup program when you turn on the power. Settings can be accessed via arrow keys. Press to choose an option to configure the system properly.
ENDAT-K1001 USERS MANUAL UNICORN COMPUTER CORP. 3-1. Main The Standard Setup is used for the basic system configuration, such as date etc. ˙AMIBIOS, Processor, System Memory. These Items show the firmware and hardware specifications. ˙System Time This setting allows you to set system time. The time format is Hour:Minute:Second. ˙System Date This setting allows you to set system Date. The time format is Momth:Day:Year. 3-2. Advanced Use this menu to setup items of special feature.
ENDAT-K1001 USERS MANUAL UNICORN COMPUTER CORP. CPU Configuration PowerNow This setting enables/disables the generation of ACPI_PPC, _PSS, and _PCT objects.
ENDAT-K1001 USERS MANUAL UNICORN COMPUTER CORP. SuperIO Configuration Serial Port 1/2 Address Select an address and a corresponding interrupt for the specified serial port. Restore on AC Power Loss by IO Power Off Leaves the computer in the power off state. Power On Leaves the computer in the power on state. Restores the system to the previous status before Last State power failure or interrupt occurred.
ENDAT-K1001 USERS MANUAL UNICORN COMPUTER CORP. Hyper Transport Configuration HT Link Speed This item allows you to set the Hyper-Transport Link Speed. Setting to “Auto” the system will detect the HT link Speed automatically. HT Link Control These Items allow you to set the Hyper-Transport Link width. Setting to “Auto” the system will detect the HT link width automatically. ACPI Configuration Suspend Mode This item specifies the power saving modes for ACPI function.
ENDAT-K1001 USERS MANUAL UNICORN COMPUTER CORP. C1E Support When the C1E Support (Enhanced Halt Powerdown State) is enabled, the processor will transition to a lower core to bus ratio and lower voltage ID driven by the processor to the voltage regulator before entering Halt Powerdown State (C1). Not all porcessors support Enhanced Halt Powerdown State (C1E). USB Configuration Legacy USB Support Set to [Enabled] if you need to use any USB 1.1/2.
ENDAT-K1001 USERS MANUAL UNICORN COMPUTER CORP. 3-3. Boot Use this menu to specify the priority of boot devices. Boot Settings Configuration: Quick Boot Enabling this setting will cause the BIOS power-on self test routine to skip some of its tests during bootup for faster system boot. Quiet Boot This BIOS feature determines if the BIOS should hide the normal POST messages with the motherboard or system manufacturer’s full-screen logo.
ENDAT-K1001 USERS MANUAL UNICORN COMPUTER CORP. PS/2 Mouse Support Select support for PS/2 Mouse. Wait For “F1” If Error When this setting is set to [Enabled] and the boot sequence encounters an error, it asks you to press F1. If disabled, the system continues to boot without waiting for you to press any keys. Boot Device Priority The items allow you to set the sequence of boot devices where BIOS attempts to load the disk operating system. First press to enter the sub-menu.
ENDAT-K1001 USERS MANUAL UNICORN COMPUTER CORP. User Password / Change User Password User Password controls access to the system at boot. These settings allow you to set or change the user password. Boot Sector Virus Protection This function protects the BIOS from accidental corruption by unauthorized users or computer viruses. 3-5. Chipset This menu controls the advanced features of the onboard Northbridge and Southbridge.
ENDAT-K1001 USERS MANUAL UNICORN COMPUTER CORP. Internal Graphics Configuration: Internal Graphics Mode This setting specifies the internal graphics mode. UMA Frame Buffer Size Frame Buffer is the video memory that stores data for video display (frame). This field is used to determine the memory size for Frame Buffer. Larger frame buffer size increases video performance. Side-Port Clock Speed This setting is selecting the clock speed of the onboard video memory.
ENDAT-K1001 USERS MANUAL UNICORN COMPUTER CORP. Panel ID Selection 800x600x18bit_1CH 1920x1080x24bit_2CH Reserved 1024x768x24bit_1CH 800x480x18bit_1CH Reserved 1280x1024x24bit_2CH 640x480x18bit_1CH Reserved 1366x768x24bit_1CH Reserved Reserved 1680x1050x24_2CH Reserved LCD Disable. Select appropriate LCD type according to the above Panel ID. If the LCD panel spec is not suitable for above list, please contact UNICORN for OEM BIOS/VBIOS request.
ENDAT-K1001 USERS MANUAL UNICORN COMPUTER CORP. Realtek 8111C PCIE NIC This setting enables/disables the onboard LAN controller. Realtek 8111C Option ROM The items enable or disable the initialization of the onboard LAN Boot ROM during bootup. Selecting [Disabled] will speed up the boot process. 3-6. Power Use this menu to specify your settings for power management.
ENDAT-K1001 USERS MANUAL UNICORN COMPUTER CORP. 3-7. Exit This menu allows you to load the BIOS default values or factory default settings into the BIOS and exit the BIOS setup utility with or without changes. Save Changes and Exit Save changes to CMOS and exit the Setup Utility. Discard Changes and Exit Abandon all changes and exit the Setup Utility. Discard Changes Abandon all changes and continue with the Setup Utility.
ENDAT-K1001 USERS MANUAL UNICORN COMPUTER CORP. Chapter 4. VGA, LCD and drivers 4-1. Graphic controller Feature The ENDAT-K1001 integrated ATI Radeon™ HD 3200 graphics with ATI Avivo™ HD technology provides excellent graphics performance for most embedded applications.
ENDAT-K1001 USERS MANUAL UNICORN COMPUTER CORP. 4-2. Driver Utility Installation Guide 1. When finishing the installation of Windows XP, please install the relative AMD display and AUDIO driver manually for compliance compatibility of hardware environment. 2. Please contact sales department of UNICORN for Embedded OS user driver (Windows CE and Windows XP embedded). All of embedded OS driver is not be included in any versions of driver CD-ROM from UNICORN.
ENDAT-K1001 USERS MANUAL UNICORN COMPUTER CORP. Appendix A: FLASH Memory Utility Using this utility to update the system BIOS from a disk file to the on board Flash memory. Be aware the improper change of the system BIOS will cause the system to malfunction. Using utility as follows: 1. Insert the FLASH memory utility distribution floppy diskette in drive A: 2. At the DOS prompt, type A:> AFUD4310.EXE BIOS.rom /C /X /REBOOT 3.
ENDAT-K1001 USERS MANUAL UNICORN COMPUTER CORP. Appendix B: LIMITED WARRANTY Standard Two years limited warranty on all our ENDAT series all-in-one motherboards and embedded board. Products that become defective during the warranty period shall be repaired, or subject to manufacturer’s option, replaced. The limited warranty applies to normal proper usage of the hardware and does not cover products that have been modified or subjected to unusual electrical or physical stress.
ENDAT-K1001 USERS MANUAL UNICORN COMPUTER CORP. RMA SERVICE REQUEST FORM When requesting RMA service, please fill out this “RMA Service Request Form”. This form needs to be shipped with your returns. Service cannot begin until we have this information. RMA NO.: Company: Person to Contact: Phone No: Purchase Date : Fax No. : Applied Date : Return Shipping Address: Model No. Serial No.
ENDAT-K1001 USERS MANUAL UNICORN COMPUTER CORP. Issue Code of defect. 01 Second Times R.M.A.
