Specifications

197
Item # Description Code List Price
L-com Cable Testers
2006-2007 Master Catalog
Prices and specifications subject to change.
E-mail: [e-mail] Fax: [phone] Toll Free: 1-800-343-1455 Hours: Mon - Thu 8am-6pm,Fri 8am-5pm EST
L-c om
®
CONNECTIVITY
PRODUCTS
© 2006 L-com,Inc. All Rights Reserved. L-com Connectivity Products and the L-com logo are registered marks.
One or more items in a product family are
RoHS compliant and/or partially compliant.
Access www.L-com.com for latest status.
Portable Cable Testers - Indispensable Tools for the Cable Installer or Technician
Our DX series of cable testers are invaluable tools for bench and remote testing of modular, coaxial and twinaxial cable testing. All the units are built within
a black ABS plastic case which can handle the abuse of even the roughest installer or technician. Modular patch cord testers utilize two high grade modular
jacks for input and output connection to telco cables. Coaxial and twinaxial testers come complete with termination units which allow the technician to
test remote cable runs. All of our DX and DXB series testers are exclusively designed and manufactured by L-com. Custom designs will be considered for
volume users or OEM’s by calling our Technical Support Department at 1-800-343-1455.
Coaxial Remote Cable Testers for Testing Extended Cable Runs
L-com’s coaxial remote cable testers facilitate fast, simple continuity testing of common types of cabling. Each kit is equipped with a tester unit and a
terminating device which allows verification of permanently installed cabling as well as patch cords. To test, just fasten the termination device to one end
of cable and verify results at the opposite end with the master unit. Good continuity, shorts and opens, are all identified by reading the LEDs on the
faceplate. The DX35A is used for coaxial cables with BNC, TNC, or Wang (BNC+TNC) connectors. Each model includes an installed 9V alkaline battery as
well as a carrying case for storage. Appropriate terminators are included. Outside dimensions are: 3.8" x 2.4" x 1.1".
DX35A Coaxial (BNC and TNC) Remote Cable Tester A, B 24.95
DXBCC Carrying Case for DX Testers 3.99
BNC Coaxial Tester with Intermittent Grabber
The DXB4 contains circuitry for locating intermittent shorts that can be almost impossible to locate. Simply plug both ends of a coaxial cable into the BNC
jacks and observe the three LEDs. Intermittent shorts that are normally shown as a flickering LED or a moving needle on an Ohm meter are locked-on
with the exclusive intermittent grabber circuitry. The tester can be combined with adapters to test terminations other than BNC, SMA or F adapters. Unit
comes complete with an installed 9V alkaline battery. Leatherette case supplied only with kits.
DXB4 BNC Coax Cable Tester with Intermittent Grabber A 17.50
DXBCC Carrying Case for Tester and Terminators 3.99
Coax Adapter Kit for L-com's DX Testers
This flexible adapter kit allows you to test coaxial cables terminated with SMA, RCA and F style connectors. These versatile adapters easily connect to the
BNC ports of L-com's DX Coax testers.Now,with one test kit it is possible to test coax cables used in CATV,Audio and Data applications.Includes a 1-
year manufacturer's warranty.
DX-COAX-ADPT Coax Adapter Kit C, D, E 12.99
MICROPULSE™ Fiber Optic Light Source - Simple Location of Fiber Runs
This unit eases the difficulty of tracing fiber optic cable runs within a building by using new MICROPULSE technology. Presently, to trace multimode
terminated fiber runs, two types of equipment can be used. The first, a laser source, is expensive and potentially dangerous to one’s eyesight if viewed
directly. These units work well for locating breaks in fiber runs, however, the cost of the units often exceed $500. The second method is to use an
incandescent light source (simple flashlight) with a coupler to connect to the fiber optic termination. These devices produce a low intensity light signal
which is difficult to see by the human eye at the far end of the run.
L-com’s solution to this problem was simple: Produce a low cost, high intensity light source that is safe to use and easy for the eye to locate. This was
done by creating exclusive circuitry that produces an extremely bright red light source which is focused into the fiber optic cable. The light is then pulsed
in an on-off manner that is easier for the human eye to locate, especially from a group of fiber runs commonly found in wiring closets or central wiring
points. A multi-use coupler is also utilized so that connection to ST, SC, FC, RSD and FSD can be done without additional coupling adapters or cables.
• Ultra High Intensity Red Source LED (660nm, 1400 mcd) • Dual Output - Pulsed or Steady Light Signal
• Exclusive MICROPULSE Signal Pulse Technology (Patent Pending) • Runs on One 9V Alkaline Battery (Included)
• Multi-Use Coupler Accepts Fiber Connectors with 2.5mm Ferrule
DXL10 MICROPULSE Fiber Optic Light Source 39.95
Micropulse™ Fiber Optic Light Source Kit - Everything for Tracing Multimode Runs
We now offer in kit form our popular Micropulse Fiber Optic Light Source with common adapters used in toning out fiber optic runs. Included in the kit is
the DXL10 Micropulse light source, 2 ST-ST simplex couplers, 1 FC-FC simplex coupler, 1 SC-SC duplex coupler, 1 SC-ST duplex adapter and 1 simplex
ST-SC multimode patch cord. Also included is a plastic box for organizing the couplers and a belt mountable carrying case. A $160.00+ value if purchased
separately.
DXL10K1 MICROPULSE Fiber Optic Light Source Kit 69.00
Shielded RJ45 Breakout Box - Exclusively Designed and Manufactured by L-com
L-com’s DXR45S breakout box is intended for modifying the wiring in modular cords terminated by RJ45 plugs. The unit incorporates two high grade
shielded RJ45 jacks, a nine position dip switch and dual nine position headers. Jumper wires are included in the rear compartment. This unit does not
utilize a battery, its intention is for modifying modular cable wiring only.
DXR45S Shielded RJ45 Breakout Box 17.00
DX35A
DXB4
DXR45S
PATENTED
DXL10K1
Kit
DXL10
Exclusive Made in USA
DX-COAX-ADPT
BNC TNC F Type SMA RCA
A
B C D E
Code shows tester
ability to check:
Distributors Wanted - Call 1-800-343-1455
2K6_MV2_NW&TestEquip_2.qxd 09/07/06 4:56 PM Page 197
DXL10K1
DXL10K1
DXR45S
DXR45S
DXL10
DXL10
DXBCC
DXBCC
DXB4
DXB4
DX35A
DX35A
DX-COAX-ADPT
DX-COAX-ADPT