Specifications

ManualsBrandsUNICOM ManualsComputer equipmentFEP-72107T

908 Canada Court

City of Industry, CA 91748 U.S.A.

Phone: 626.964.7873 or 800.346.6668 Fax: 626.964.7880

www.unicomlink.com e-mail: info@unicomlink.com

©UNICOM 2004. UNICOM and “A Network Systems Solution” are trademarks of UNICOM Electric, Inc.

Rev: 02.04

USER’S MANUAL

FEP-5300TF-C ( SC/Multi-Mode/2km )

FEP-5300TF-T ( ST/Multi-Mode/2km )

FEP-5300TF-M ( MT-RJ/Multi-Mode/2km )

FEP-5400TF-C

( SC/Single Mode/15km )

FEP-5401TF-C ( SC/Single Mode/30km )

FEP-5402TF-C ( SC/Single Mode/60km )

10/100Base-TX/100Base-FX

Fast Ethernet Converter

For full coverage of your warranty, be sure

to register your product using the enclosed

registration card.

Summary of content (8 pages)

PAGE 1
For full coverage of your warranty, be sure to register your product using the enclosed registration card. 10/100Base-TX/100Base-FX Fast Ethernet Converter FEP-5300TF-C FEP-5300TF-T FEP-5300TF-M FEP-5400TF-C FEP-5401TF-C FEP-5402TF-C 908 Canada Court City of Industry, CA 91748 U.S.A. Phone: 626.964.7873 or 800.346.6668 Fax: 626.964.7880 www.unicomlink.com e-mail: info@unicomlink.com ©UNICOM 2004. UNICOM and “A Network Systems Solution” are trademarks of UNICOM Electric, Inc. All rights reserved.
PAGE 2
PAGE 3
Package Contents Package contents include the following: ■ 10/100Base-TX to 100Base-FX Converter (Multi-Mode or Single Mode) ■ DC Power Adapter ■ User’s Manual ■ Rack Mount Brackets ■ Warranty card (not shown) 10/100Base-TX/FX User’s Manual Converter (Multi-Mode or Single Mode) Power Adapter Rack Mount Brackets Figure 1. Contents of package. IMPORTANT: If any piece is missing or damaged, please contact your local dealer or reseller for service.
PAGE 4
Introduction Congratulations on purchasing a quality UNICOM product. Unicom’s VELOCITY Series represents the newest, most advanced generation of signal conversion technology. This converter is designed to expand your network through a fiber optic connection extending a fiber link up to 60 km (Single mode in full duplex mode). The 10/100TX/100FX Converters offer the most popular fiber cabling connectors: MT-RJ, SC, and ST formats in Multi-mode and SC in Single Mode.
PAGE 5
Work Stations Hardware Description The Front Panel 1 2 3 4 4 FEP-5300TF-C 2km off on 1 2 3 4 3 2 1 off on DIP Setting UTP2 UTP Fast Ethernet Switch The Front Panel of the 10/100TX/100FX converters consists of one RJ-45 Port ( Auto MDI/MDIX ), 6 LED Indicators (TX SPD, LK/ACT, FDX/COL, Fiber LK/ACT, FDX and PWR ) and one fiber 100Base-FX Port.
PAGE 6
Product Specifications LED Indicators There are six diagnostic LEDs located on the Front panel of these Converters. The LEDs provide real-time information on system status. The indicators include Power, UTP 100, LK/ACT, FDX/COL, Fiber LK/ACT, and FDX/COL. The following table provides descriptions of the LEDs. LED Status Color Description PWR On Green • The converter is supplied with suitable power.
PAGE 7
Troubleshooting DIP Switch • Verify that you are using the right power adapter ( DC 9V, 700mA ). Using a power adapter with DC output greater than 9V could result in damage to the unit and/or personal injury. The DIP-switches are used to configure operation mode for LLF ( Link Loss Forwarding ) and operation modes for the UTP/Fiber ports. • Check the configuration DIP switch. It must be set in the same operation mode as its link partner. • Confirm the proper UTP/Fiber cable is being used.
PAGE 8
Network Connection C. Use a screwdriver to attach the rack mount ears to both sides of the modular converter. A. Select the appropriate length Category 5e or 6 twisted pair cable. Connect one end of the twisted pair cable to the RJ-45 connector on the converter and the other end of twisted pair cable to the RJ45 connector on any 10/100Base-TX device. D. Install the modular converter by inserting it into the chassis guides and sliding it in until it stops.