Datasheet

ManualsBrandsUNI-T ManualsSignal GeneratorsFunction Generator, 1x 5MHz

UTG1000A Series Function Generator User Manual

1.2 General Safety Overview

This instrument strictly complies with the GB4793 safety requirements for electrical equipment and

EN61010-1/2 safety standard during design and manufacturing. It complies with the safety standards

for insulated voltage standard CAT II 300V and contamination level II.

Please read the following safety preventative measures:

To avoid electric shock and fire, please use the dedicated UNI-T power supply appointed to the local

region or country for this product.

This product is grounded through the power supply ground wire. To avoid electric shock, grounding

conductors must be connected to the ground. Please be sure that the product is properly grounded

before connecting to the input or output of the product.

To avoid personal injury and prevent damaging the product, only trained personnel can perform the

maintenance program.

To avoid fire or electric shock, please notice rated operating range and product marks. Do not use the

product outside the rated range.

Please check the accessories for any mechanical damage before usage.

Only use accessories that came with this product.

Please do not put metal objects into the input and output terminals of this product.

Do not operate the product if you suspect it is faulty, and please contact UNI-T authorized service

personnel for inspection.

Please do not operate the product when the instrument box opens.

Please do not operate the product in humid conditions.

Please keep the product surface clean and dry.

If the equipment is used in a manner not specified by the manufacturer, the protection provided by the

equipment may be impaired.

Summary of content (6 pages)

PAGE 1
UTG1000A Series Function Generator User Manual 1.2 General Safety Overview This instrument strictly complies with the GB4793 safety requirements for electrical equipment and EN61010-1/2 safety standard during design and manufacturing. It complies with the safety standards for insulated voltage standard CAT II 300V and contamination level II.
PAGE 2
UTG1000A Series Function Generator User Manual Chapter 2 Introduction This device is economical, high-performance, multi-functional single channel waveform generators. It uses direct digital synthesis (DDS) technology to produce accurate and stable waveforms, with a resolution as low as 1μHz. It can generate accurate, stable, pure and low distortion output signals, also can provide high-frequency vertical edge square waves.
PAGE 3
UTG1000A Series Function Generator User Manual 12.Menu 11. Number Buttons Button 13.Function Menu Softkeys 1. Multifunctional Knob and Button 1.Display 9.Directional Buttons 2.On/Off Button 8.CH Control/ Output Terminal 3.Menu Operation Softkeys 4. Auxiliary Function and System Settings Buttons 6. 5.Manual Trigger Button Modulation/ 7. Synchronous Frequency Output Meter Input Terminal Terminal/ Trigger Output Terminal Figure 2-1 1. Display Screen 4.
PAGE 4
UTG1000A Series Function Generator User Manual 4. Auxiliary Function and System Settings Button This button includes 3 function labels: Channel settings, frequency meter, and system. A highlighted label (the midpoint of the label is gray and font is pure white) has a corresponding sub label at the bottom of the display. 5. Manual Trigger Button Setting trigger, and carrying out manual trigger when flashing. 6.
PAGE 5
UTG1000A Series Function Generator User Manual The rear panel is shown in figure 2-2: Figure 2-2 1. USB Interface PC software is connected through this USB interface. 2. Heat Dissipation Holes To ensure this instrument dissipate heat well, please do not block these holes. 3. Insurance Pipe When AC input current is more than 2A, the fuse will cut off the AC input to protect the device. 4. Main Power Switch Press down on “I” to power the instrument, and press down on “O” to cut off AC input. 5.
PAGE 6
UTG1000A Series Function Generator User Manual Function interface is shown in figure 2-3: Channel Information Waveform Parameter List Softkey Labels Softkey Labels Figure 2-3 Detailed Description: ² Channel information: 1) “ON/OFF” on the left is channel open information. 2) There is a “Limit” logo indicates output range limit where white is valid and grey is invalid. The matched impedance of output terminal (1Ω to 1KΩ adjustable, or high resistance, factory default is 50Ω).