PREFACE Thank you for purchasing the new UT343D coating thickness gauge. In order to use this product safely and correctly, please read this manual thoroughly, especially the Safety Instructions part. After reading this manual, it is recommended to keep the manual at an easily accessible place, preferably close to the device, for future reference. Software and user manual can be found by searching UT343D on our official website, then go to the ‘Docs & Software’ tab.
Table of Contents Ill. Safety Instructions. IV. Function Description V. Operating Instructions — VI. Performance indexes UT343D USER MANUAL UT343D USER MANUAL I. Overview UT343D is a high-accuracy coating thickness gauge, which can measure coating thickness on both ferrous and non-ferrous metals. This device has features of high precision and non-destructive measurement, and functions of single-point, multi-point averaging algorithm and quick judgment.
UT343D USER MANUAL Ii. Accessories Open the packing box and take out the gauge. Please double check whether the following ems are deficient or damaged. 1. The gauge Nurseryman qpg 3. Standard coating thickness 1st {5 pcs) 4, Substantiation —7 ™M8M 1 pc §. Nonferrous substrate —F—— 1 pc 6. Sensor cover — 1pc 7. Hand opg 1pC 8. USB cab ——7M8Mm8 — HF pc 9. AA alkaline battery UT343D USER MANUAL iil. Safety Instructions 1. Please perform the two-point calibration before using the gauge.
UT343D USER MANUAL UT343D USER MANUAL IV. Function Description B. Display interface description 1. Menu Icon description A. Structure description x warming fight Prompt tone setting Back light setting Unit setting 3. Power button Calibration mode setting Higher limit setting Lower limit setting 4. Set/Confim/Callbrate button LED waning light setting Flory reset Delete stored data 5. Cancel/Clear button Continuous measurement setting 6. judgment button 7. screen button 8. Sensor assembly 9.
UT343D USER MANUAL UT343D USER MANUAL V. Operating Instructions 8. When measuring, select 3 to 5 measuring points on the surface of the measured object evenly, measure 5 A. Replace the battery: times for each measuring pint, and take the average value of the 5 mes as the Indicating value of the point. 1. Tum the locking screw on the battery compartment counterclockwise, open the battery cover, and install 2 7.
UT343D USER MANUAL UT343D USER MANUAL 1.
UT343D USER MANUAL 8. Factory reset 2) Select the factory rests icon #) by using the 3 and buttons, short press the [8 button to enter the factory rests menu, tum on/off the factory reset by using the ‘3 and 5&7 buttons, and short press the button to confirm the factory reset or & button to exit. 9.
UT343D USER MANUAL 4) Chang the measurement position, measure 3 times near the new position, and the gauge will count the average value of 3 times into point B. 6) Measure and E (5 points) according to the above method. 6) After the measurement, the screen displays the average values of the 5 points and the judgment result “PASS” or “FAIL"). 7) Short pass the 5 button to rectum or long press the 5 button to exit. G.
UT343D USER MANUAL 4) Press the [2] button to confirm the adjustment (or & button fo cancel the calibration. 5) Figure 6 appears on the screen, prompting users to place the gauge vertically on the undercoated substrate. 6) Lift it up after 2s. Zero will be displayed (as shown in Figure 7), and the gauge will automatically exit to the normal measurement mods. 7) At this point, the two-pant calibration Is completed. Figure 5 Figure & Figure 7 UT343D USER MANUAL 3.
UT343D USER MANUAL UT343D USER MANUAL Vl. Performance indexes Alarm India Tha LED lights up in the compounding color when the value im Indication exceeds the set vagus rang for lama. A. Technical specifications cloaca Indentation Measurement and alarm are accompanied by Function Measuring range| Thickness | Resolution | Accuracy Explanation corresponding prompt tones. verse | 0.1um I, Limit setting ‘Any limit vale can be set between 0~1200pm.
B. General specifications 1. Display: 4-digit color LCD display 2. Refresh rate: 0.55 3. Sensor type: Magnetic Induction and eddy current composite sensor 4. Impact resistance: The gauge can withstand 1 meter drop 5. Power requirement: AA alkaline battery (2 pes) 6. Dimensions: 152mm*85mm*35mm 7.
UT343D USER MANUAL LINO-T.
