UNI FLAME AUTOLIFT PRO-CRAFT SERIES 210/240 MIG Manual 240 Volt Standard MIG / MAG
UNI FLAME AUTOLIFT 3YEARS Warranty * Machine Model Description MIG Inverter Part Number KPC210 / 240 CONTENTS PAGE No: Safety Main Parameter. Machine Features Installation & Operation Caution Maintenance Troubleshooting 3 4 4 4 11 12 12 Machine Model This welding equipment for industrial and professional use conforms to IEC 60974 International Safety Standard. We hereby state that we provide three year of guarantee for this welding Power Source from the date of purchase.
SAFETY Welding and cutting equipment can be dangerous to both the operator and people in or near the surrounding working area, if the equipment is not correctly operated. Equipment must only be used under the strict and comprehensive observance of all relevant safety regulations. Please read and understand this instruction manual carefully before the installation and use/operation of this equipment. not switch the function modes while the machine is operating.
UNI FLAME AUTOLIFT PART NUMBER PRIMARY INPUT VOLTAGE Ieff WELDING CURRENT VOLTAGE STEPS DUTY CYCLE 40°C KPC210 240V 1 Phase 16Amps 30-210 Amps 8 18% @ 210 Amps 24.5V 60% @ 110 Amps 19.5V 100% @ 95 Amps 18.75V WELDING VOLTAGE RANGE DC 15.5V – 24.5V WIRE SIZE (mm) 0.6 – 0.9mm Ferrous 0.8 – 0.9mm Stainless Steel 0.8 – 1.0mm Aluminium 0.8 – 1.0mm Flux Cored DIMENSIONS (mm) 920 x 460 x 820mm WEIGHT (Kgs) 78 Kgs KPC240 240V 1 Phase 20Amps 30-240 Amps 8 15% @ 240 Amps 26V 60% @ 150 Amps 21.
UNI FLAME AUTOLIFT 2.4 GAS BOTTLE INSTALLATION Put the gas bottle in vertical position on the gas bottle holder plane and position the bottle so that it is lays on the gas bottle holder and fix it with the chain and the spring clip, like in pic E. Tightly connect the gas hose, which comes from the back of the machine to the brass nipple of supplied regulator adjust argon regulator to deliver the required litres per minute. NOTE. reffer to instruction manual of argon regulator for proper use. 2.
UNI FLAME AUTOLIFT Mod.B Mod.A LEGENDA: LEGENDA: LED 1 = Thermal protection LED 2 = Trigger normal – Manual welding LED 3 = Trigger latch – Automatic welding LED 4 = Stich welding LED 5 = Spot welding S1 = Menù. To select welding parameter on the display S2 = Mode. To select welding type on the led welding parameter DISPLAY = Show welding parameter ENC = Encoder LED = Thermal protection 4.
Wire speed: It is possible to regulate the wire speed using the knobs of the encoder 2) Pregas: It is possible to regulate the gas open time using the knob of the encoder before the arc prime 3) Ramp up: It is possible to regulate the wire increasing gradually using the knobs of the encoder in order to have the one selected at point 4.2.1 4) Burn back: it is possible to regulate, using the knob of the encoder, the wire length came out at the end of welding process.
UNI FLAME AUTOLIFT WELDING GUIDE GENE G ENER EN NER N E GENERAL RULE When welding on the lowest output settings, it is necessary to keep the arc as short as possible. This should be achieved by holding welding torch as close as possible and at an angle of approximately 60 degrees to the workpiece. The arc length can be increased when welding on the highest settings, an arc length up to 20 mm can be enough when welding on maximum settings.
UNI FLAME AUTOLIFT DESCRIPTION OF GRAPHICS
A D B C E F G H I L M N UNI FLAME AUTOLIFT
O P UNI FLAME AUTOLIFT
1. Working Environment. 1.1 1.2 1.3 1.4 The environment in which this welding equipment is installed must be free of grinding dust, corrosive chemicals, flammable gas or materials etc, and at no more than maximum of 80% humidity. When using the machine outdoors protect the machine from direct sun light, rain water and snow etc; the temperature of working environment should be maintained within -10°C to +40°C. Keep this equipment 30cm distant from the wall for ventilation.
MAINTENANCE WARNING: Exposure to extremely dusty, damp, or corrosive air is damaging to the welding machine. In order to prevent any possible failure or fault of this welding equipment, clean the dust at regular intervals with clean and dry compressed air of required pressure.
