Camera Network Camera Quick Guide UD.
Network Camera·Quick Guide Thank you for purchasing our product. If there are any questions, or requests, please do not hesitate to contact the dealer. This manual applies to DS-2CD2712F-I(S), DS-2CD2732F-I(S) cameras. This manual may contain several technical incorrect places or printing errors, and the content is subject to change without notice. The updates will be added to the new version of this manual. We will readily improve or update the products or procedures described in the manual.
Network Camera·Quick Guide Regulatory Information FCC Information FCC compliance: This equipment has been tested and found to comply with the limits for a digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
Network Camera·Quick Guide equipment, or dispose of it at designated collection points. For more information see: www.recyclethis.info. 2006/66/EC (battery directive): This product contains a battery that cannot be disposed of as unsorted municipal waste in the European Union. See the product documentation for specific battery information. The battery is marked with this symbol, which may include lettering to indicate cadmium (Cd), lead (Pb), or mercury (Hg).
Network Camera·Quick Guide Safety Instruction These instructions are intended to ensure that user can use the product correctly to avoid danger or property loss. The precaution measure is divided into “Warnings” and “Cautions” Warnings: Serious injury or death may occur if any of the warnings are neglected. Cautions: Injury or equipment damage may occur if any of the cautions are neglected.
Network Camera·Quick Guide To reduce the risk of fire or electrical shock, do not expose this product to rain or moisture. This installation should be made by a qualified service person and should conform to all the local codes. Please install blackouts equipment into the power supply circuit for convenient supply interruption. Please make sure that the ceiling can support more than 50(N) Newton gravities if the camera is fixed to the ceiling.
Network Camera·Quick Guide Do not place the camera in extremely hot, cold temperatures (the operating temperature should be between -30°C ~ 60°C), dusty or damp environment, and do not expose it to high electromagnetic radiation. To avoid heat accumulation, good ventilation is required for a proper operating environment. Keep out of water and any liquid. While shipping, the camera should be packed in its original packing.
Network Camera·Quick Guide Table of Contents 1 Overview .................................................................................................. 8 1.1 Appearance .............................................................................................8 1.2 Wiring ....................................................................................................10 2 Installation .............................................................................................. 11 2.
Network Camera·Quick Guide 1 Overview 1.1 Appearance 3 6 2 4 5 9 1 Figure 1-1 Overview Table 1-1 Overview No.
Network Camera·Quick Guide 5 Serial Port 6 Power interface 7 Ethernet interface 8 Mounting Base 9 Lens Notes: To reset the default parameters to the camera, you need to press and hold the reset button and power on the camera. After the power on the camera, you must still press and hold the reset button for about 10 seconds. The DS-2CD2712F-IS and DS-2CD2732F-IS models support audio and alarm functions. The interfaces are shown as follows.
Network Camera·Quick Guide 1.
Network Camera·Quick Guide 2 Installation Before mounting, please make sure that the device in the package is in good condition and all the assembly parts are included. Notes: Please make sure that the device in the package is in good condition and all the assembly parts are included. Check the specification of the products for the installation environment. Make sure that all the related equipment is power-off during the installation.
Network Camera·Quick Guide Black Liner Lower Dome Screws Figure 2-1 Remove the Lower Dome and Black Liner 2.2 Mounting 2.2.1 Ceiling mounting Steps: 1. Disassemble the camera. Refer to the section 2.1. 2. Attach the drill template (supplied) to the place where you want to fix the camera. 3. According to the drill template as shown in Figure 2-2, drill three screw holes in the ceiling.
Network Camera·Quick Guide 4. If you want to route the cables inside the ceiling, drill a cable hole in the ceiling according to the drill template. Skip this step, if you want to route the cables on the surface of the ceiling. Refer to Conduit Installation on the Side for side cable routing. 5. Attach the camera to the ceiling by aligning the holes of the back box with the holes on the ceiling. 6. Secure the camera with the supplied screws as shown in Figure 2-3.
Network Camera·Quick Guide 9. Adjust the image and focus. Please refer to the section 2.3 for more detailed information. 10. Install the inner black liner back to the camera. 11. Install the lower dome back to the camera and secure it with screws as shown in Figure 2-4. Figure 2-4 Secure Black Liner and Lower Dome Conduit Installation on the Side If you want to route the cables from side of the camera, you need to follow the steps below to install a conduit for cable routing. Steps: 1.
Network Camera·Quick Guide Water-proof Plug Side Outlet Figure 2-5 Remove the water-proof plug 2. Route the power cable and network cable through the side outlet to the conduit. 3. Align and rotate clockwise the conduit to the side outlet tightly.
Network Camera·Quick Guide Note: For wall mounting, position the side outlet directly downward for water proofing. Downward Figure 2-7 Side Outlet Direction 2.2.2 Ceiling mounting with gang box Steps: 1. Disassemble the camera. Refer to the section 2.1. 2. Install the gang box in the ceiling. 3. Attach the mounting base to the gang box with two screws.
Network Camera·Quick Guide 4. Route the cables through the hole in the center of the mounting base. 5. Align the camera with the mounting base. 6. Tighten the screws to secure the camera with the mounting base. 7. Connect the video output connector to the monitor. Connect the power connector to the power supply. 8. Adjust the image and focus. Please refer to the section 2.3 for more detailed information. Figure 2-9 Secure Camera 9. Install the inner black liner back to the camera.
Network Camera·Quick Guide 10. Align the lower dome with the camera. 11. Tighten the screws to secure the lower dome with the camera as shown in Figure 2-10. Figure 2-10 Secure Lower Dome 2.2.3 Wall Mounting For the wall mounting, you have to purchase a wall mount. Steps: 1. Disassemble the camera. Refer to the section 2.1. 2. Install the wall mount and mounting adapter as shown in Figure 2-11. 3. Align the screw holes of the mounting base with the corresponding screw holes of the mounting adapter. 4.
Network Camera·Quick Guide Mounting Adapter Figure 2-11 Install the Mounting Adapter Mounting Base Figure 2-12 Secure Mounting Base 19
Network Camera·Quick Guide 5. Route the cables through the hole in the center of the wall mount. 6. Align the camera with the mounting base. 7. Tighten the set screws to secure the camera with the mounting base. 8. Connect the video output connector to the monitor. Connect the power connector to the power supply. 9. Adjust the image and focus. Please refer to the section 2.3 for more detailed information.
Network Camera·Quick Guide 10. Install the inner black liner back to the camera. 11. Align the lower dome with the camera. 12. Tighten the screws to secure the lower dome with the camera. Black Liner Lower Dome Figure 2-14 Secure Black Liner and Lower Dome 2.3 Image and Focus Adjusting Steps: 1. Three-axis adjustment. 1). View the camera image using the monitor. 2). Rotate the panning table to adjust the panning position of the camera. 3).
Network Camera·Quick Guide 4). Rotate the lens table to adjust the azimuth angle of the image. Panning Tilting Rotation Figure 2-15 Three-axis Adjustment 2. Zoom and focus adjustment. 1). View the camera image using the monitor. 2). Loosen the zoom lever and move the lever between T(Tele) and W(Wide) to obtain the appropriate angle of view. 3). Tighten the zoom lever. 4). Loosen the focus lever and move the lever between F(Far) and N(Near) to obtain the optimum focus. 5). Tighten the focus lever.
Network Camera·Quick Guide Lever Lever Figure 2-16 Lens Adjustment 23
Network Camera·Quick Guide 3 Setting the Network Camera over the LAN Purpose: To view and configure the camera via LAN (Local Area Network), you need to connect the network camera in the same subnet with your PC. Then, install the SADP or iVMS-4200 software to search and change the IP of network camera. The following figure shows the cable connection of network camera and PC: Figure 3-1 Wiring over LAN Set the IP address of the camera for accessing via LAN. Steps: 1.
Network Camera·Quick Guide 2. Change the IP address and subnet mask to the same subnet as of your PC. Refer to the following introductions to set IP address with SADP software: Search active devices online Search online devices automatically: After launch the SADP software, it automatically searches the online devices every 15 seconds from the subnet where your computer locates. It displays the total number and information of the searched devices in the Online Devices interface.
Network Camera·Quick Guide Note: Device can be searched and displayed in the list in 15 seconds after it goes online; it will be removed from the list in 45 seconds after it goes offline. Search online devices manually: You can also click to refresh the online device list manually. The newly searched devices will be added to the list.
Network Camera·Quick Guide 3). Enter the password of the admin account of the device in the Password field and click to save the changes.
Network Camera·Quick Guide 3. Enter the IP address of network camera in the address field of the web browser to view the live video. Notes: The default value of the IP address is 192.0.0.64. The default user name is admin, and password is 12345. For accessing the network camera from different subnets, please set the gateway for the network camera after you log in.
Network Camera·Quick Guide 4 Accessing via Web Browser System Requirement: Operating System: Microsoft Windows XP SP1 and above version / Vista / Win7 / Server 2003 / Server 2008 32bits CPU: Intel Pentium IV 3.0 GHz or higher RAM: 1G or higher Display: 1024×768 resolution or higher Web Browser: Internet Explorer 7.0 and above version, Apple Safari 5.02 and above version, Mozilla Firefox 3.5 and above version and Google Chrome8 and above version Steps: 1. Open the web browser. 2.
Network Camera·Quick Guide Figure 4-1 Login Interface 5. Install the plug-in before viewing the live video and managing the camera. Please follow the installation prompts to install the plug-in. Note: You may have to close the web browser to finish the installation of the plug-in.
Network Camera·Quick Guide Figure 4-2 Download Plug-in Figure 4-3 Download Plug-in 31
Network Camera·Quick Guide Figure 4-4 Install Plug-in Figure 4-5 Install Plug-in 32
Network Camera·Quick Guide 6. Reopen the web browser after the installation of the plug-in and repeat the above steps 2-4 to login. Note: For detailed instructions of further configuration, please refer to the user manual of network camera.
Network Camera·Quick Guide 0
