Camera Network Camera Quick Guide UD.
Network Camera·Quick Guide Thank you for purchasing our product. If there are any questions, or requests, please do not hesitate to contact the dealer. This manual applies to DS-2CD2612F-I(S), DS-2CD2632F-I(S) cameras. This manual may contain several technical incorrect places or printing errors, and the content is subject to change without notice. The updates will be added to the new version of this manual. We will readily improve or update the products or procedures described in the manual.
Network Camera·Quick Guide Regulatory Information FCC Information FCC compliance: This equipment has been tested and found to comply with the limits for a digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
Network Camera·Quick Guide equipment, or dispose of it at designated collection points. For more information see: www.recyclethis.info. 2006/66/EC (battery directive): This product contains a battery that cannot be disposed of as unsorted municipal waste in the European Union. See the product documentation for specific battery information. The battery is marked with this symbol, which may include lettering to indicate cadmium (Cd), lead (Pb), or mercury (Hg).
Network Camera·Quick Guide Safety Instruction These instructions are intended to ensure that user can use the product correctly to avoid danger or property loss. The precaution measure is divided into “Warnings” and “Cautions” Warnings: Serious injury or death may occur if any of the warnings are neglected. Cautions: Injury or equipment damage may occur if any of the cautions are neglected.
Network Camera·Quick Guide To reduce the risk of fire or electrical shock, do not expose this product to rain or moisture. This installation should be made by a qualified service person and should conform to all the local codes. Please install blackouts equipment into the power supply circuit for convenient supply interruption. Please make sure that the ceiling can support more than 50(N) Newton gravities if the camera is fixed to the ceiling.
Network Camera·Quick Guide Do not place the camera in extremely hot, cold temperatures (the operating temperature should be between -30°C ~ 60°C), dusty or damp environment, and do not expose it to high electromagnetic radiation. To avoid heat accumulation, good ventilation is required for a proper operating environment. Keep out of water and any liquid. While shipping, the camera should be packed in its original packing.
Network Camera·Quick Guide Table of Contents 1 Overview .................................................................................................. 8 1.1 Appearance .............................................................................................8 1.2 Wiring ....................................................................................................10 2 Installation .............................................................................................. 11 2.
Network Camera·Quick Guide Overview Appearance 1 8 6 4 5 11 9 2 3 10 7 Figure 1-1 Overview Table 1-1 Overview No.
Network Camera·Quick Guide 4 IR LED 5 Lens 6 Air Vent 7 Video Output Interface 8 Integrated Bracket 9 Reset Button 10 SD Card Slot 11 Power Interface 12 Network Interface Notes: To reset the default parameters to the camera, you need to press and hold the reset button and power on the camera. After the power on the camera, you must still press and hold the reset button for about 10 seconds. The DS-2CD2612F-IS and DS-2CD2632F-IS models support audio and alarm functions.
Network Camera·Quick Guide Wiring Figure 1-3 Wiring 10
Network Camera·Quick Guide Installation Before mounting, please make sure that the device in the package is in good condition and all the assembly parts are included. Notes: Please make sure that the device in the package is in good condition and all the assembly parts are included. Check the specification of the products for the installation environment. Make sure that all the related equipment is power-off during the installation.
Network Camera·Quick Guide Remove the front cover by rotating it counterclockwise as shown in Figure 2-1(right). Figure 2-1 Disassemble the Camera Insert the SD card to the SD card slot. Rotate the front cover clockwise back to the camera and install the sun shield according to the arrow direction as shown in Figure 2-2(right).
Network Camera·Quick Guide Slide the sun shield according to the arrow direction as shown in Figure 2-3(left). Rotate the TW M3X5 screw clockwise to tighten the sun shield. Rotating Label Figure 2-3 Assemble the Camera Note: For water-proof, please align the rotating label on the front cover with that on the camera when you rotate the front cover clockwise. Refer to Figure 2-3(right). Mounting This camera is equipped with a bracket on the bottom.
Network Camera·Quick Guide 1. Attach the drill template (supplied) to the wall where the camera is to be mounted. Drill screw holes in the wall according to the number one holes of the drill template. Refer to the Figure 2-4. 2 Screw Hole 1 1 2 Cable Hole 2 2:Screw Hole for Mounting Base 1 1:Screw Hole for Bracket 1 2 Figure 2-4 Drilling Holes in the Wall If you need to route cables through the wall(or ceiling), cut a cable hole according to the drill template.
Network Camera·Quick Guide Route the cables of the camera. Secure the camera to the wall(or ceiling) with expansion screws. Refer to the Figure 2-5. Figure 2-5 Secure the Camera Wall Mounting with a Junction Box Before you start: For mounting with a junction box, you have to purchase a junction box.
Network Camera·Quick Guide 1. Attach the drill template (supplied) to the wall where the camera is to be mounted. Drill holes in the wall according to the number two holes of the drill template. Refer to the Figure 2-4. If you need to route cables through the wall(or ceiling), cut a cable hole according to the drill template. Skip this step, if you want to route the cables on the surface of the ceiling. Secure the junction box to the wall with expansion screws. Route the cables of the camera.
Network Camera·Quick Guide Figure 2-6 Secure the Camera Wall Mounting with a Gang Box Before you start: For mounting with a gang box, you have to purchase a gang box. Steps: 1. Secure the camera attachment to a gang box with screws. Route the cables of the camera. Secure the camera to the camera attachment with screws. Refer to the Figure 2-7.
Network Camera·Quick Guide 3-axis (pan/tilt/rotation) adjusting allows adjustment for optimum camera rotation and placement. You can use this function to get the angle of view that you want. Pan Adjustment Steps: 1. Loosen the lock screw-1. Adjust the panning position of the camera. The adjusting range is from 0 degrees to 360 degrees. Tighten the lock screw-1. Tilt Adjustment Steps: 1. Loosen the lock screw-2. Adjust the tilting position of the camera. The adjusting range is from 0 degrees to 90 degrees.
Network Camera·Quick Guide Lock Screw-1 Pan Rotation Tilt Lock Screw-2 Lock Screw-3 Figure 2-8 Lens Adjustment Zoom and Focus Adjusting Purpose: You can use the zoom lever and focus lever to adjust the zoom value and focus value. Steps: 1. Disassemble the camera. Refer to section 2.1. 2. View the camera image using the monitor. Loosen the zoom lever and move the lever between T(Tele) and W(Wide) to obtain the appropriate angle of view. Tighten the zoom lever.
Network Camera·Quick Guide Lever Lever Figure 2-9 Zoom and Focus Adjustment 20
Network Camera·Quick Guide Setting the Network Camera over the LAN Purpose: To view and configure the camera via LAN (Local Area Network), you need to connect the network camera in the same subnet with your PC. Then, install the SADP or iVMS-4200 software to search and change the IP of network camera. The following figure shows the cable connection of network camera and PC: Figure 3-1 Wiring over LAN Set the IP address of the camera for accessing via LAN. Steps: 1.
Network Camera·Quick Guide 2. Change the IP address and subnet mask to the same subnet as of your PC. Refer to the following introductions to set IP address with SADP software: Search active devices online Search online devices automatically: After launch the SADP software, it automatically searches the online devices every 15 seconds from the subnet where your computer locates. It displays the total number and information of the searched devices in the Online Devices interface.
Network Camera·Quick Guide Note: Device can be searched and displayed in the list in 15 seconds after it goes online; it will be removed from the list in 45 seconds after it goes offline. Search online devices manually: You can also click to refresh the online device list manually. The newly searched devices will be added to the list.
Network Camera·Quick Guide 3). Enter the password of the admin account of the device in the Password field and click to save the changes.
Network Camera·Quick Guide Enter the IP address of network camera in the address field of the web browser to view the live video. Notes: The default value of the IP address is 192.0.0.64. The default user name is admin, and password is 12345. For accessing the network camera from different subnets, please set the gateway for the network camera after you log in.
Network Camera·Quick Guide Accessing via Web Browser System Requirement: Operating System: Microsoft Windows XP SP1 and above version / Vista / Win7 / Server 2003 / Server 2008 32bits CPU: Intel Pentium IV 3.0 GHz or higher RAM: 1G or higher Display: 1024×768 resolution or higher Web Browser: Internet Explorer 7.0 and above version, Apple Safari 5.02 and above version, Mozilla Firefox 3.5 and above version and Google Chrome8 and above version Steps: Open the web browser.
Network Camera·Quick Guide Figure 4-1 Login Interface Install the plug-in before viewing the live video and managing the camera. Please follow the installation prompts to install the plug-in. Note: You may have to close the web browser to finish the installation of the plug-in.
Network Camera·Quick Guide Figure 4-2 Download Plug-in Figure 4-3 Download Plug-in 28
Network Camera·Quick Guide Figure 4-4 Install Plug-in Figure 4-5 Install Plug-in 29
Network Camera·Quick Guide Reopen the web browser after the installation of the plug-in and repeat the above steps 2-4 to login. Note: For detailed instructions of further configuration, please refer to the user manual of network camera.
Network Camera·Quick Guide 0
