941014 DF941014 Toyota Tacoma 5’ Short Bed 2016-Current Hardware (Box 1 of 2) 1. Tango front rail assembly 2. Tango left rail assembly 3. Tango right rail assembly 4. Rhino Rack cross bars (2) 5. 3mm allen wrench 6. Spacers (2) 7. Bulkhead square seal (2) 8. T-Track clamps (6) 9. Spacers (6) 10. Mounting bolts (6) 11. Flat washers (6) Lock washers (6) 12. Bulkhead seal 13. B-Light 14. Rhino Rack leg kit (2) Hardware (Box 2 of 2) 1. Mounting brackets (2) 2. Gas props (2) 3. 5mm allen wrench 4.
Tango Track Installation 2 1 x3 1. Clean the bulkhead and install the bulk head seal. 2. Remove plastic end cap from track rail and insert three t-track clamps. 3 Side Seal - Correct Side Seal - Incorrect 3. Place the right Tango rail assembly onto the truck bed, according to the drawing, the spacers should go between the tango and the truck bed. Note: Be sure side rubber is not pinched under the Tango rail.
Tango Track Installation (continued) Side Seal - Correct Side Seal - Incorrect 5. Slide the left rail assembly in place by inserting the L bracket in to the T-slot, do not tighten Note: Lift up on the front rail assembly to create enough room to insert the L bracket into the T-slot. Note: Be sure side rubber is not pinched under rail assembly. Tighten clamps 1st Tighten L brackets 2nd 6. Push Tango system towards bulkhead, install all remaining clamps and tighten.
Ridgelander Bracket Installation 7. Slide four (4) M8 t nuts into each tango side rail track. Using the M8 bolts, flat washers and lock washers attach the front brackets and the striker brackets according to the measurements below. 2 3/8” 3 1/8” 8. Position the front mounting brackets 3 1/8” from the plastic corner piece of the Tango Track. Position the rear striker brackets 2 3/8” from the rear of the extrusion. UnderCover, Inc. (866) 900-8800 Page 4 www.undercoverinfo.com © 2016 UnderCover, Inc.
Ridgelander Cover Installation Line Up Slot Push Forward Tighten Knob 9. With some assistance place the cover onto the front mounting brackets. . Line the open slot up in the hinge with the pin on the mounting bracket. Push the cover forward to lock it into place. Tighten knob until it stops, it may be necessary to push the hinge up tight to the mounting bracket to help the threads engage, be careful not to cross thread and strip the bracket. 10.
Ridgelander Cover Adjustment To adjust, move front mounting brackets only 12. With your cover closed, take a quick inspection to make sure that the cover is sitting square to the Tango Track. To adjust the cover front to back evenly, move both of the front mounting brackets forward or rearward accordingly. To adjust to one side or the other, move the front mounting brackets forward or rearward independently. 13. Close the cover and check that the latches properly engage to the striker bracket.
Rhino Rack Rhino Rack Manual For installation instructions and load ratings for the Rhino Rack system, refer to the Rhino Rack Manual. Truck Owners Manual Be sure to refer to the truck owners manual for load ratings for the truck. When calculating weight of cargo, be sure to include occupants and the Ridgelander Cover. Ridgelander with rack system = 125lbs Caution To Prevent damage or loss of cargo when driving, check to make sure cross bars and cargo are securely fastened.
Ridgelander Removal and Reinstall REMOVAL Remove front flap from track Disconnect prop, snap into J-clip Loosen knob on hinge With assistance, slide cover rearward apx 1”, lift straight up and remove cover REINSTALL With assistance, set cover on Line Up Slot Attach props Push Forward Attach front flap Tighten Knob UnderCover, Inc. (866) 900-8800 Page 8 www.undercoverinfo.com © 2016 UnderCover, Inc. All rights reserved.
Ridgelander Warranty IMPORTANT! - ACTIVATE YOUR WARRANTY AT UNDERCOVERINFO.COM Be sure to activate your warranty within 30 days of your purchase. Failure to do so can complicate or void future warranty procedures. Serial Number Date of Purchase Thank you for purchasing the UnderCover Ridgelander truck bed cover. We are proud to have you as a customer and believe you will be pleased with the years of service your UnderCover will provide.
