Liquor Cabinet Assembly Instructions - Please keep for future reference WF294858/WF294859 Dimensions Width - 54inch Depth - 15.7inch Height - 31.
! Safety and Care Advice Important – Please read these instructions fully before starting assembly • Check you have all the components and tools listed on the following pages. • During assembly do not stand or put weight on the product, this could cause damage. • Remove all fittings from the plastic bags and separate them into their groups. • Assemble the item as close to its final position (in the same room) as possible.
Components - Fittings Please check you have all the panels listed below Note: The quantitie below are the correcet amount to complete the assembly. In some cases more fittings may be supplied than are required. A B C Male Camlock x 62 Female Camlock x 62 Dowel x 34 D E F Shelf Support Pin x 8 6*50mm Screw x 8 G H Drawer slider 14" x 1 Hex Key x 1 I 3*12mm Screw x 32 Drawer slider 12" x 3 J K L Door stopper x 4 3.
Using Camlocks Step 1 Connect the male camlock as diected in the assembly instructions using a scewdriver. 1 Step 2 DO NOT OVER TIGHTEN. NE PAS SERRER EXCESSIVEMENT. 2 Push the male camlock into the entry hole. 4 Step 3 3 Step 4 Insert the female camlock as shown in the instruction. Turn the female camlock clockwise with a screwdriver. Note：ensure that the arrow on the top of the camlock points towards the entry hole for the male camlock.
Assembly Instructions 16 15 14 28 11 15 30 11 29 28 27 31 29 26 26 27 26 27 25 24 8 23 13 9 10 7 12 7 4 5 6 17 17 20 21 1 22 19 3 18 2 32 32
Assembly Instructions Step 1 A C A A C 3 A C A C 2 A A C 1 A C C C Step 2 1 B B 2 B 1 B 2 3
Assembly Instructions Step 3 B B 3 2 B B 1 1 3 2 Step 4 C C 6 C A C C A C 4 C C C C 5 C C
Assembly Instructions Step 5 G1 G2 G1 G2 Step 6 1 5 B B 4 I G1 I 2 3
Assembly Instructions Step 7 3 6 4 1 5 E 2 E E E F Step 8 7 6 4 1 5
Assembly Instructions Step 9 C C C A 8 A A C 9 C C A Step 10 1 2 3 B B 8 B B 9
Assembly Instructions Step 11 K K 8 K Q K K K K Q K Step 12 H1 H2 H1 H2 X3
Assembly Instructions Step 13.1 Step 13.
Assembly Instructions Step 15 A 8 A A A Step 16 1 B B 8 6 7 B 4 B 1 5 2 3
Assembly Instructions Step 17 7 7 10 Step 18 I I G1 I 13 I I H1 H1 I 12
Assembly Instructions Step 19 A X11 13 A X9 12 C C Step 20 1 2 9 8 6 4 5 1 B B B B B B B B B B B 13 3
Assembly Instructions Step 21 1 2 12 B B 9 B B B B B 8 6 B 4 B 1 5 13 Step 22 15 14 15 3
Assembly Instructions Step 23 A A A A A 16 A A A Step 24 1 16 B B B B 13 B B B B 12 2 3
Assembly Instructions Step 25 D D D D 13 D 12 D D D D 4 6 Step 26 D 17 D 17
Assembly Instructions Step 27 R 20 R 21 19 R R Step 28 22 20 19 21
Assembly Instructions Step 29 A A N A A 18 N P Step 30 1 2 B I B 18 I I 22 G2 B B 20 I 19 21 G2 3
Assembly Instructions Step 31 R 27 R 28 26 X2 R R Step 32 27 29 26 28 X2
Assembly Instructions Step 33 R 27 R 30 26 R R Step 34 27 31 26 30
Assembly Instructions Step 35 A A O O A A A 23 A O O P A A A 24 A O O P A 25 A P Step 36 1 I H2 I 28 B I B 27 29 H2 I 26 B 25 B 2 3
Assembly Instructions Step 37 1 2 3 2 3 I H2 I 30 B I B H2 31 27 I 26 B B 24 Step 38 1 I H2 I 28 B I B 27 29 H2 I 26 B 23 B
Assembly Instructions Step 39 T T T T T T 1 X20 3 2 25 T 24 T T T T T T T 23 18 1 T T T 2 3 Step 40 K J K X2 K 32 K J O O P
Assembly Instructions Step 41 J K X4 K X4 4 K X4 J K 32 X4 32 Step 42 J K K X4 X4 K 12 32 J 32 K X4 X4
Assembly Instructions Step 43 M L M Step 44 The unit is floor standing, but it is recommended that the unit is secured to the wall. 1. Move the unit into desired position. 2. Mark the wall with a suitable scribe the position of the fixing holes. Warning: ! Before driling,check wall for hidden pipes and cables. 3. Drill holes and insert 2 x wall plug 4. Attach 2 x Wall Straps to to the top of the unit using 2 x Washers and 2 x Screws 5.
Assembly Instructions Step 45 The unit is floor standing, but it is recommended that the unit is secured to the wall. 1. Move the unit into desired position. 2. Mark the wall with a suitable scribe the position of the fixing holes. Warning: ! Before driling,check wall for hidden pipes and cables. 3. Drill holes and insert 2 x wall plug 4. Attach 2 x Wall Straps to to the top of the unit using 2 x Washers and 2 x Screws 5.
