Warranty
Remote control
●
+ button
+
●
Presetting temperature can be decreased.
Press this button, the temperature can be
- button
-
set up, continuously press this button
and hold
contents can
( F)
signal
The
ailable
can
be sent by if pressing this button.
For presetting temperature increasing.
Press this button,can set up the temperature,
when unit is on . Continuously
press and
hold this button for more than 2 seconds,
the corresponding contents will be
changed
rapidly, until unpress the button
laying all along. In Auto mode, the temp-
erature can not be set up, but operate this
button can send the signal. Centigrade
setting range :16-30; Fahrenheit scale
setting range 61-86.
then send the information, is disp-
●
By pressing this key under switch-off state,
you
setting is 0.5 ~ 24 hours. The characters "T-ON"
and "H" will flash for 5 seconds. Within 5 seconds,
you may make one press of this key to complete
the sttingand send the message.If the setting is
valid, the set time will be displayed for 2 seconds
before display of the temperature message.
During
and press "-" key to decrease
the value. The time will
increase or decrease
by 0.5 hours with each press
of this key.If pressing "+" or "-" key continuously,
timer setting, and there is no display of "T-ON" or
cancel
the auto switch-on.When the temperature
"T-On" and "H" will display
constantly for 2 seconds.
TIMER button
TIMER
0.25 seconds. After being energized, the
fault is no
"H". Press
ON/OFF key to switch on the unit and
By pressing this key under switch-on state,
set the
The method of setting as the same as for
auto switch-on.
●
-18-
C
(
F
)
OPERATION OF WIRELESS REMOTE CONTROL
this button
for two seconds, the relative
quickly change, until unhold
and send the order that the C
will be displayed all the time.
temperature adjustment is unav-
under the Auto mode, but the order
time for auto switch-off.
After 2 seconds,the preset
temperature will be displayed.
cancel
the auto switch-on and send the message.
you may.
within these 2
seconds,you may press this key again to
troller can increase the set time by 0.5 hours every
display becomes constant, you
maypress
this key
may set the time for auto switch-on. The
range of
flash,you may press "+" key to
increase the value
the time value will change rapidly.The remote
con
again to display the remaining set
time. The time value,
Touche VEILLE
•
Appuyez sur cette touche, Veille On et Veille Off peut être sélectionné. Après avoir mis sous tension, Veille Off est
réglé par défaut. Après que l'appareil est éteint, la fonction de veille est annulée. Après fonction de veille mis en
place, le signal du Veille s'affiche. Dans ce mode, le temps de temporisation est réglable. Sous les modes Auto et
Ventilateur, cette fonction n'est pas disponible.
Touche Ventilateur
• En appuyant sur cette touche, vous pouvez sélectionner AUTO, Ventilateur 1, Ventilateur 2, Ventilateur 3 ou
Ventilateur 4, et peut également basculer entre eux. Ventilateur 4 uniquement en mode de refroidissement. Après
avoir été sous tension, AUTO est réglé par défaut. Seule ventilateur FAIBLE peut être réglé en mode SEC, cette
touche ne peut pas régler le la vitesse du ventilateur, mais peut envoyer un message.
(Remarque : Lorsque vous sélectionnez ventilateur 4, la vitesse du ventilateur est le même que ventilateur 3 sur cet
appareil)
Touche SWING
Remarque : Non disponible sur cet appareil
• Appuyez sur cette touche pour activer ou désactiver le swing.
-18-