Instructions / Assembly

ManualsBrandsUnbranded ManualsPlayground Sets & EquipmentSwirl Outdoor Music Playset Accessory

SWIRL

The stunning sculptural design exudes both beautiful

sounds and visual art. The Chimes are made of durable,

resonated anodized aluminum, and range from soprano

to alto. One Side of the Swirl plays the key of C and the

other the key of A Minor.

GOLD C MAJOR / SILVER A MINOR PENTATONIC

PROPRIETARY AND CONFIDENTIAL

THE INFORMATION CONTAINED IN THIS

DRAWING IS THE SOLE PROPERTY OF

FREENOTES HARMONY PARK. ANY

REPRODUCTION IN PART OR AS A WHOLE

WITHOUT THE WRITTEN PERMISSION OF

FREENOTES HARMONY PARK IS

PROHIBITED.

FREENOTES HARMONY PARK

194 BODO DRIVE, UNIT F

DURANGO CO 81303

TEL: (970) 375-7825

FAX: (970) 247-0856

EMAIL: INFO@FREENOTESHARMONYPARK.COM

WWW.FREENOTESHARMONYPARK.COM

PRODUCT SHEET / INSTALLATION GUIDE

SHEET 1 OF 6

SWIRL 2016

SCALE: 1:16

Summary of content (6 pages)

PAGE 1
SWIRL The stunning sculptural design exudes both beautiful sounds and visual art. The Chimes are made of durable, resonated anodized aluminum, and range from soprano to alto. One Side of the Swirl plays the key of C and the other the key of A Minor. GOLD C MAJOR / SILVER A MINOR PENTATONIC 1 54 4 " 1 48" 3 56 4 " FREENOTES HARMONY PARK 194 BODO DRIVE, UNIT F DURANGO CO 81303 TEL: (970) 375-7825 FAX: (970) 247-0856 EMAIL: INFO@FREENOTESHARMONYPARK.COM WWW.FREENOTESHARMONYPARK.
PAGE 2
MOUNTING OPTION IDENTIFICATION: This instrument is offered with various mounting options. Identify your option below and follow installation instructions on the following sheets. Recycled Post In-Ground Sheet 3 of 6 Steel Post In-Ground Sheet 3 of 6 Steel Post Surface Mount Sheet 4 of 6 Parts List: Swirl Instrument Assembly (1) In-Ground Post (2) 1 1/4" Tamper-Resistant Screw (12) Security Driver (1) T25 Torx, 4" lg.
PAGE 3
RECYCLED AND STEEL POST IN-GROUND INSTALLATION PROCEDURES Step 1: Excavate two 10" diameter hole, 36" deep, and 32" on center at the installation location. Contractor can modify post to desired height. Post Length = Frost Depth (36" Recommended) + Finished Height (Refer to Height Guideline) Step 2: Lower the posts into the excavated holes. Step 3: Refer to sheet 6 for installation of instrument to posts.
PAGE 4
STEEL POST SURFACE MOUNT INSTALLATION PROCEDURES Step 1: Determine installation location. Verify concrete footing is a minimum of 6" thick. If the concrete pad is at an angle, steel washers are required to act as shims. (Shims not provided) Step 2: Stand the surface mount post upright onto the concrete pad with a 32" offset on center. Mark the center of the holes on the surface mount plates. After you have made your marks, set aside the posts in order to drill for anchor holes.
PAGE 5
WALL MOUNT INSTALLATION PROCEDURES Step 1: Mount the Wall Mount Posts to playing surface at the desired Finished Height, (Refer to Finished Height Guideline) and at 32" on center. If mounting to concrete use the provided Anchor Bolts. Anchor holes should be drilled to a depth of 3" with a 3/8" Masonry Bit. The same steps 2 and 3 on Sheet 4 can be used for Anchor Bolt installation.
PAGE 6
INSTRUMENT TO POST INSTALLATION PROCEDURES Step 1: To ease the installation of the Swirl a 2x4 Brace has been added to the back of the Instrument. When the Swirl is face down there is some flex that is not present when it is upright. To install the Swirl have two people pick it up, rotate it to where it is upright, remove the brace than continue to the next step. Step 2: (Recycled Post Only) With two people, situate the instrument onto the posts.