Full Product Manual

ManualsBrandsUnbranded ManualsHeating, Venting & Cooling11 in. x 48 in. Corrugated Ridge Vent in Black (12-Piece per Case)

SUPER RIDGE

SERIES: SPECIFICATIONS

Certified Net Free Air Pitches Profile Warranty

12.7 Sq. in.

15.8 Sq. in.

19 Sq. in.

3/12 to 20/12

4 Layer (CHDPE)

5 Layer (CHDPE)

6 Layer (CHDPE)

Lifetime

Manufacturer

Lifetime

Manufacturer

Lifetime

Manufacturer

SUPERIOR

Ridge Vent Systems

SUPER RIDGE

SERIES RIDGE VENTS

Corrugated High Density Shingle Over Ridge Vent

Florida Building Code Test Protocols for the High Velocity Hurricane

Zone (HVHZ) Testing Application Standard (TAS) No. 100(A)-95:

+ ASTM D3746 impact resistance testing

+ NFVA calculations from labs for Average Net Free Ventilation Area

+ Static Pressure Uplift Test ASTM E330 35, 70, 90, 110 mph psf

+ NFVA- Net Free Ventilation Area determined

+ Wind-Driven Rain per TAS 100(A) 100ml water @ 110 mph

+ ASTM D1929 (Self-Ignition Temp 650 F)

+ ASTM D635 (Burn Rate C1, C2)

www.superridge.com

SUPER RIDGE

SUPERFLO RIDGE

SUPERFLO MAX

Handmade in the U.S.A.

The Super Ridge

Series Vents provide exceptional ventilation on any roof surface!

> Asphalt Shingles

> Metal

> Cedar Shakes

> Stone Coated Steel

> Flat Tiles

Super Ridge

Series

uses Corrugated High Density Polyethylene (CHDPE) sheets,

providing increased strength that creates a uniform ridgeline on virtually any roof pitch.

Super Ridge

Series maximizes the ventilation performance of the entire roof system

with up to 19 sq. inches of ventilation per lineal foot.

Super Ridge

Series is cut in 4 ft. lengths for fast and accurate installations.

Super Ridge

Series is available in Super Ridge

Superflo Ridge

and Superflo MAX

Widths available in 7, 8.5 & 11 inch wide.

ICC AC132 Acceptance Criteria for Attic Vents Effective March 1, 2010

+ NFVA 4.1 Net Free Ventilation Area determined in Section 4.1

+ UBC 26-6/ASTM D1929 (1975) Self-Ignition Section 3.2.3

+ UBC 26-7 (Burn Rate C1, C2)

+ Dust Exposure Test: Section 4.2.

+ Temperature Cycling: Section 4.3

+ Weathering Test: Section 4.4 (-40 to 180 degrees)

ASTM D 638 and ASTM D 1499

+ Resistance to Wind-Driven Rain: Section 1505.3 Florida Building Code,

TAS 100(A) 35, 70, 90, 110 mph

+ Quality Control: Documented quality control program,

per Sections 5.0,5.1,5.2

www.superridge.com

Summary of content (8 pages)

PAGE 1
www.superridge.com SUPER RIDGE© SERIES RIDGE VENTS Corrugated High Density Shingle Over Ridge Vent The Super Ridge© Series Vents provide exceptional ventilation on any roof surface! > Asphalt Shingles > Metal > Cedar Shakes > Stone Coated Steel Handmade in the U.S.A. > Flat Tiles Super Ridge© Series uses Corrugated High Density Polyethylene (CHDPE) sheets, providing increased strength that creates a uniform ridgeline on virtually any roof pitch.
PAGE 2
SUPERIOR Ridge Vent Systems www.superridge.com SUPER SOFFIT© VENTS Corrugated High Density Polyethylene Soffit Vent The Super Soffit© vent increases air flow and ease of installation! • Super Soffit© uses 4 mm x 750 GSM Corrugated High Density Polyethylene (HDPE) sheets, providing increased strength that creates a superior balanced ventilation system. • Super Soffit© Series maximizes the ventilation performance of the entire roof system with up to 10 sq. inches of ventilation per lineal foot.
PAGE 3
The importance of Balanced Attic Ventilation (BAV) SUPERIOR Ridge Vent Systems www.superridge.com Superior Ridge Vents and Super Soffit© vents create a perfect Balanced Attic Ventilation system. BAV allows air to flow through your attic space and back outside effortlessly. Since the flow of exhaust air is limited to the intake air, proper consideration is needed when planning your BAV system. Superior Ridge Vents recommends a ventilation system with 50% Super Ridge vents and 50% Super Soffit vents.
PAGE 4
SUPERIOR Ridge Vent Systems SUPER RIDGE©Series Installation instructions Handmade in the U.S.A. Easy Installation: One person can easily install the 4 ft. ridge vent sections. All you need is a circular saw, chalk line, hammer, utility knife and tape measure. Installation is for a standard gable roof application: FIG. 2 FIG. 1 1. Make sure ridge line has a 3" slot, 1 1/2" each side of ridge centerline.
PAGE 5
Figure 1 To create an end cap for a Super Ridge vent: Figure 2 Fig. 2. A longitudinal strip is removed from each lower corrugated layers adjacent side edge to create a flap from the extending portion of the upper sheet of corrugated mterial. Fig. 3. The flap is then folded over the side edges of the lower corrugated layers to provide an end cap from the ridge of a roof. Nail end to roof to complete seal and end cap.
PAGE 6
SECTION 07723 RIDGE AND SOFFIT VENTS PART 1 GENERAL SECTION INCLUDES: A. Ridge vents. B. Soffit vents. C. Hip vents. 1.2 RELATED SECTIONS A. Section 06100 - Rough Carpentry. B. Section 07310- Shingles. C. Section 07320 - Roof Tiles. D. Section 07410- Metal Roof and Wall Panels. 1.3 SUBMITTALS A. Submit under provisions of Section 01300. B. Product Data: Manufacturer's catalog data, standard details, and installation instructionss C.
PAGE 7
PART 2 PRODUCTS 2.1 MANUFACTURER A. Manufacturer: Provide vents fabricated (Handmade in the USA) by: Superior Ridge Vent Systems 3929 Martin Way East, Suite B Olympia, WA 98506 Telephone: (815)388-7820 Email: sales@tmjarchitectural.com Website: www.tmjarchitectural.com 2.2 MATERIALS A. Ridge Vents- General: ICC AC132 Certified- Manufactured in America of corrosion-free, extruded, high-density polyethylene B. Ridge Vents: Superior Ridge SuperFlo Max© Ridge Vent 1. Certified Net Free Area: 12.
PAGE 8
MacArthurCo PRO RIDGE SERIES SUPERIOR Ridge Vent Systems www.superridge.com SUPER RIDGE© SERIES Testing & Certifications Handmade in the U.S.A. ICC AC132 Acceptance Criteria for Attic Vents Effective March 1, 2010 + NFVA 4.1 Net Free Ventilation Area determined in Section 4.1 + UBC 26-6/ASTM D1929 (1975) Self-Ignition Section 3.2.3 + UBC 26-7 (Burn Rate C1, C2) + Dust Exposure Test: Section 4.2. + Temperature Cycling: Section 4.3 + Weathering Test: Section 4.