Installation Guide

ManualsBrandsUnbranded ManualsBathLavish 33-1/2 in. L x 59 in. W x 87 in. H Center Drain Alcove Shower Stall Kit in Black and Chrome with Easy Fit Drain

Shower & Bath Enclosure

Installation Instructions

Thank you for purchasing Freshjet Shower products. We are committed to providing our

customers with high quality products at a competitive price.

Please read all instructions carefully before and during installation

★Professional help is required for installation.

These installation instructions should be used as a guideline. Your specific shower or

bath enclosure may differ from the figures shown in these instructions. This instruction

is for shower models as follows: S-3460, SE-3460, and SL-3460.

★Additional Installation Tools:

3” Dry wall screws

Silicone sealant Phillips head screwdriver Flat head screwdriver

Power drill Polyurethane Foam (4 cans)

★Prepare Mounting Boards

Mount 54” (2X4) boards to the backwall studs horizontally at 82-1/4” (top edge) above

the floor and 2” from the sidewalls. The top frames of shower’s backwalls shall be

attached to this board.

★The shower is delivered in a wood crate with carton box contents as follows:

Box 1: Two big side aluminum-framed glass panels

Box 2: Function panel with pressure valve, water hoses, body jets, and electronic

control

Box 3: Two framed glass back wall panels

Box 4: Shower base and top, and hardware box

Box 5: Two front panels, top and bottom tracks, two 90 degree aluminum channel angles

Summary of content (10 pages)

PAGE 1
Shower & Bath Enclosure Installation Instructions Thank you for purchasing Freshjet Shower products. We are committed to providing our customers with high quality products at a competitive price. Please read all instructions carefully before and during installation ★Professional help is required for installation. These installation instructions should be used as a guideline. Your specific shower or bath enclosure may differ from the figures shown in these instructions.
PAGE 2
★Hardware included: 1. Drain with flexible hose if you ordered 1-1/2” drain. It doesn’t come with a drain piece or flexible hose if you ordered 2” drain. You can buy 2” drain such as Oatey at a hardware store. 2. Cup washers and decorative chrome covers for mounting the function panel to back walls 3. 7/8” iron screws (8pieces), ½” stainless steel screws (20 pieces), and 1/4" (4 pieces) screws 4. Glass shelf and its mounting bolts, washers, rod connectors and nuts 5.
PAGE 3
c. Install the 54” long 2X4 board to the backwall studs horizontally at 82-1/4” (top edge) above the floor and 2” from the sidewall or corner. d. 120V wall outlet preferably located at 82” above the floor 16” from the corner so that you can access it easily for the future. ★2. Base PreparationS-3460 Base Preparation: https://youtu.be/ltiGsR16G_I a. Remove the shower base from its packaging. b.
PAGE 4
l. Easy-Fit Drain Connections Recommendations: For remodeling and when the floor drain and shower drain don’t line up, please use Easy-Fit Drain as follows: (i). Use 4” to 1-1/2” PVC Reducing Coupling (Canplas 193023) to reduce the 4” floor drain to 1-1/2”. Don’t glue down until all parts lined up and tested fit! (ii). Use 1-1/2” X1-1/4” PVC 90 degree elbow to reduce the drain pipe further to 11/4”. There are other ways to reduce 1-1/2” to 1-1/4” too. (iii).
PAGE 5
h. Please check this video: S-3460 Front Frame Assembly: https://www.youtube.com/watch?v=6Jotui2rvrk ★4. Front frame assembly: connection of glass panels to tracks a. Attach the inside-edge of the front panel to the tracks with panel clips.
PAGE 6
b. Use Part#C1 and C2glass clip to fix the glass to the tracks, top and bottom. ★5. Glass Door Assembly a. Install the door rollers as shown below. The screws in the top rollers are for the height adjustment. The springs in the bottom rollers push the rollers upward against the U track. b. Locate handle holes on the doors and install water seal strips with magnets (dark brown) on the edges near the door handles and clear strips (4) to the other edges as shown by the illustration. c.
PAGE 7
★6. Back wall Assembly a. Install glass shelf, hand-held sliding bar, towel bar if applicable, soap/shampoo dispensers if applicable, mirror if applicable, through-wall elbows to back walls through pre-drilled holes. b.
PAGE 8
Hand-held shower Hand-shower head sliding bar Hand-held shower water hose connection from the elbow ★7. Glass Door Installation (Do this step after step 9) a. Put rollers on top of the doors into the top rail first. b. Then put the rollers on the bottom into the bottom rail by pushing the rollers downward to cut into the U tracks. c. Adjust the screws on the top rollers if necessary. d. Install the door handles. e. Install the magnetic door seals to the front edges of the doors. f.
PAGE 9
Door roller in top track (31 stands for glass) Door roller in lower track ★8. Unit Assembly 9 a. Connect the front frame to the channeled angles on both sides (drawing on page 3) b. Connect left back panel to the left side panel from the back with ½” screws and set them in place on the base. c. Connect right back panel to the right side panel from the back with ½” screws and set them in place on the base. d. Place front-frame-angles assembly onto the base. You need two people to move the assembly.
PAGE 10
★9. Unit installation a. Connect and secure all water lines to the shower enclosure. Make sure all connections are water tight! If your unit comes with a built-in radio, plug it into a 120V outlet. b. Match up the electrical wire connectors (by pictures on the tags) for LED lights, speaker, and fan. (The DC powers both lights If your unit has both dome and panel LED lights.) c. You may apply silicone sealant to the outer edge of the base. d. Secure the unit to the wall using the 3” dry wall screws.