Instructions

ManualsBrandsUnbranded ManualsOptoelectronics & DisplaysLED remote control

K-8000C Manual

K-8000C system features:

1. 32 to 65536 degree Gray control, Gamma correction procession handle.

2. Support various point, line light source, and all kinds of rules and specific shaped handle.

3. The controller has eight ports output, each port can support up to 512/1024 lights(DMX

lights can support up to 512 pixels).

4. The playback content stored in SD card, the SD card can store up to 32 files, SD cared

capacity supports 128MB-32GB.

5. The controller can single set use,also multiple controllers cascade, cascade optical isolation

mode: interference, better stability, cascade distance between two controllers can reach up

to 150 meters, need to use 0.5M² pure copper power cord.

6. The controller support chip can lock the support IC in software, or not lock the support IC in

the software, select the support IC through the controller CHIP button, this scheme is more

flexible and convenient.

7. For the DMX lighting IC, the controller comes with write address function; In addition, with

use of our 2016 LedEdit-K V3.26 or later edition can make one key write address function

setting.

8. Support load lamp is 4 channels (RGBW) pixels, or split into single channel point pixels.

9. Enhanced 485 TTL and 485 differential (DMX) signal output.

10. The controller comes with the test effects were as follows: 1 red, green, blue and black jump;

2 red, green, blue and black gradient; 3 red, green, blue and goes.

Note:

1. The controller load lamps 512 points pixel, speed can reach up to 30 frames / sec, 768 point

pixel speed can reach up to 25 frames / sec, 1024 point pixel speed is about 22 frames / sec

(the above parameter is an example of 1903 agreement IC, different IC have difference)

2. International standard DMX512 (1990 agreement) maximum support 512 pixels. When the

load is international standard 170 pixels, the speed can reach up to 30 frames / sec, 340

pixels speed is about 20 frames / sec, when 512 pixels speed is about 12 frames / sec.

3. Timing (holidays) Play Global Wireless GPS synchronization, control station channel

distributor, please contact the salesman or technical support staff for more information.

Summary of content (8 pages)

PAGE 1
K-8000C Manual K-8000C system features: 1. 32 to 65536 degree Gray control, Gamma correction procession handle. 2. Support various point, line light source, and all kinds of rules and specific shaped handle. 3. The controller has eight ports output, each port can support up to 512/1024 lights(DMX lights can support up to 512 pixels). 4. The playback content stored in SD card, the SD card can store up to 32 files, SD cared capacity supports 128MB-32GB. 5.
PAGE 2
Support chips (PC Software Select K-8000-RGB) 00: UCS1903,1909,1912,2903,2904，2909,2912；TM1803,1804,1809,1812； SM16703，16709,16712；WS2811；INK1003；LX3203,1603,1103；GS8205, 8206；SK6812（Support up to 1024*8=8192 pixels） 01：SM16716,16726（Support up to 1024*8=8192 pixels） 02：P9813（Support up to 1024*8=8192 pixels） 03：LPD6803（Support up to 1024*8=8192 pixels） 04：LX1003,1203（Support up to 1024*8=8192 pixels） 05：WS2801（Support up to 1024*8=8192 pixels） 06：LPD1886（Support up to 1024*8=8192 pixels） 07：TM1913（Support
PAGE 3
Screen print meaning： Button meaning: Button Meaning SHIP Select chip model MODE Switch files SPEED+ Speed up SPEED- Speed down Power supply DC5V input/DC12-24 input POWER Power indicator SYNC Cascade indicator STATUS Status indicator SD CARD SD card slot Press CHIP and then MODE button, can enter write code mode, 61 means UCS512-A/B coding; 62 means WS2821 coding; 63 means SM512 coding, 64 means UCS512-C coding Press SPEED+ and SPEED- the same time, would enter effect files looping mode
PAGE 4
Conventional IC lamps wiring: Controller support DMX lights coding and wiring method: Two signal wiring diagram:
PAGE 5
Single signal wiring diagram: 1.Like the above diagram, wired the line and start the controller, press “CHIP”and “MODE” at the same time switch to coding mode, adjust to Chip: 61 that is UCS512A or B coding mode, as below: NOTE: 61 means UCS512A or B coding mode; 62 means WS2821 coding mode; 63 means SM DMX512AP; 64 means UCS512-C；Ch.
PAGE 6
2. After selection, press “MODE” to code, then the screen would display A A A. Until finished coding, it would show Writing OK, Like below: 3．After finished address code, press “CHIP” first and at the same time press “MODE”button, switch to playback mode, switch the chip to Chip: 10, this is the DMX512 standard agreement 250K playback mode.
PAGE 7
Encryption Glossary Explanation: Password is OK Num Password exist Can't repeated Set Password OK Clear Pwd OK Pwd not right No Password Has expired! Contact factory Password normal! The remaining boot times Password has existed Can’t repeat set password Password set successfully Clear password successfully Password not correct Password don’t exist Password expired, please contact the factory! Specific parameter: Memory card: Type: SD card Capacity: 128MB—32GB Format：FAT or FAT32 format Storage files: *.
PAGE 8
How to handle the common problems: Problem 1: After powered on, the controller screen display SD Error, and no effect output. Answer: The screen display SD Error means the controller did not read the SD card correctly, the exist problems as below: ①SD card is empty, has no effect files. ②The effect files *.led in SD card and the controller model is mismatch, please select correct controller model, chip model in the latest edition 2016LedEdit, and remake effect files *.led.