32 Bottle Wine Rack INSTRUCTION GUIDE 1
COMPONENTS ne a P al ert V H L omlf t t Bo She ne a P al ic ic ert V H 1x R 1x 1x l ane P ck 16x er Ba ivid D le d Mid To e -k 1x ick 1x l l Tophelf S 1x 1x TOOLS Stud CENTER 1/2" Drill Bit Rubber Mallet 3/32" Drill Bit Short Phillips Head Screwdriver Long Phillips Head Screwdriver Tape Measure Drill 32 BOTTLE WINE RACK HARDWARE 10x Plastic Dowel 10x Dowel Insert Stud Finder Hammer TOGGLE HARDWARE 10x 26x 1x Dowel Bolt Nail 2-1/4" Long Screw TETHER HARDWARE 1
1 Lay LH vertical panel on floor with holes facing up. Insert two dowel inserts (1a). Insert three plastic dowels (1b). Insert three dowel bolts (1c). 1c Dowel Bolt 1b l Plastic Dowel 1a ane P l a ic ert V H 1c L Dowel Bolt Dowel Insert 1b Plastic Dowel Insert four dowel inserts into bottom shelf. 3 Insert two plastic dowels into bottom shelf (3a). Insert two dowel inserts into toe-kick (3b).
Place bottom shelf onto LH vertical panel (4a). Make sure finished edge is facing up. Place toe-kick onto LH vertical panel (4b).
Place middle divider onto bottom shelf (5a). Insert two plastic dowels into top edge of middle divider (5b). Make sure finished edge is facing up. m ttof o B hel S Mid d le D ivid er 5b 5a 6 Insert the top two rods (opposite bottom shelf).
7 Insert remaining rods. LH Mid d Ver t ical le D ivid Pan e l er Lay RH vertical panel on floor with holes facing up. Insert two dowel inserts (8a). Insert three plastic dowels (8b). Insert three dowel bolts (8c).
9 Attach RH vertical panel. Make sure finished edge is facing up. RH Ver t ical Pan e l Insert four dowel bolts into the bottom of the top shelf and tighten with screwdriver.
11 Place safety tether onto top shelf and secure using one #6 x 5/8" screw. #6 x 5/8" Screw T Sh op el f SAFETY TETHER Install top shelf onto unit.
13 Unfold and place back panel (gray side in) onto back of unit (13a). Pull safety tether through slot on back panel (13b). 13b SAFETY TETHER 13a ac B k n Pa el 14 Secure back panel onto back of unit using nails, evenly spaced.
15 Place unit upright. 16 Move unit against wall. Locate stud in wall and center unit with stud. Mark location on wall 43" from floor for safety tether location.
17 Pull unit away from wall. Drill pilot hole in wall (17a) with a 3/32"drill bit. Secure other end of safety tether to wall using one (1) 2" long screw (17b). Move unit against wall. NOTE: If installing unit where stud is not available, anchor unit to wall using toggle and toggle bolt. 2" Long Screw 17a 17b SAFETY TETHER TOGGLE INSTALLATION 1 Using a 1/2" drill bit, drill hole into wall. Insert toggle into wall. 2 11 Slide plastic straps until they align with each other.
3 Slide plastic ring along straps until flange of ring is flush against wall. 5 Secure other end of safety tether to wall using one (1) 2-1/4" long screw. 4 Bend plastic straps back and forth until they snap off, leaving plastic ring in place.
ONE YEAR LIMITED WARRANTY COVERAGE The manufacturer warrants that the product (“Product”) you purchased will be free from defects in material and workmanship for a period of one (1) year from the date of purchase when used for single-family residential use. This limited warranty extends only to the original end user of the Product, and is not transferable.
