User Guide

ManualsBrandsUnbranded ManualsEnergy SavingLED Standalone Controller H802SE

H802SE INSTRUCTIONS

1. Introduction

H802SE can drive a variety of single or double line chips, control

maximum 6144 pixels with four output ports, the maximum clock

frequency is 2.5 MHZ, and has infrared remote control and nixie tube

display functions.

2. Controllable Driver Chips

H802SE can drive the following chips: LPD6803, LPD8806,

LPD6813, LPD1882, LPD1889, LPD6812, LPD1883, LPD1886,

DMX512, APA102, UCS6909, UCS6912, UCS1903, UCS1909,

UCS1912, WS2811, WS2812, TM1803, TM1804, TM1809, TM1812,

TM1829, TA9912, TM1913, TM1914, TM1926, WS2801, WS2803,

DZ2809, P9813, P9816, SM16716, LD151x, LD153x, MBI6021,

Summary of content (6 pages)

PAGE 1
H802SE INSTRUCTIONS 1. Introduction H802SE can drive a variety of single or double line chips, control maximum 6144 pixels with four output ports, the maximum clock frequency is 2.5 MHZ, and has infrared remote control and nixie tube display functions. 2.
PAGE 2
MBI6023, MBI6024, INK1003, LX1003, LX2003, LX2006, TLS3001, TLS3002, etc. The type of LED driver chip must be set in software, the same-timing sequence driver chips share an option. For LPD6813 and P9813, H802SE drives maximum 4608 pixels, for other chips, H802SE drives maximum 6144 pixels. 3. Clock Settings Clock frequency can be set in software as well as in controller.
PAGE 3
(1). H802SE has four output ports, each port drives maximum 1536 pixels (2). Input voltage is 5 to 24 volts DC. (3). SD card supports FAT32 and FAT16, the maximum capacity is 32G bytes, stores up to 64 DAT files. (4). The adjustable playing speed ranges from 1 to 200 frames per second, the adjustable clock frequency ranges from 0.1MHZ to 2.5MHZ. (5). H802SE has infrared remote control and nixie tube display functions. 5. Remote Control Operation (1).
PAGE 4
(4). Choose playing mode: Default playing mode is playing all DAT files in a continuous loop. “All playback” is playing all DAT files in a continuous loop. “Select playback” is playing single DAT file. In this mode, press “File” after pressing sequence number of DAT file, controller will automatically save the sequence number, next time when you power on controller, it will play the saved sequence number of DAT file. (5). Color modulation Press “Selection” to enter color modulation mode.
PAGE 5
7. Operation Manual (1). After power-on, nixie tube displays "SE". If you didn’t insert the SD card, nixie tube will keep flashing “Sd”. If controller reads SD card successfully, the nixie tube will display DAT file sequence number "F01"; "FE" means the controller type of DAT file is incorrect or pixels number is too much; "RE" means reading SD card failed, controller will retry automatically; “F0” means no valid DAT files in SD card. (2). Press "SET" on controller to save the parameters. (3).
PAGE 6
port1 port2 port3 port4 DAT1 CLK1 GND CLK2 DAT2 DAT3 CLK3 GND CLK4 D+ D- GND D- D+ D+ D- GND DAT4 D- D+ Note: due to the limitation of jacket width, two output ports share a GND. Single line driver chip only need to connect GND and DAT. 9.