Installation Guide

D
E
F
C
1 2 3 4
B
A
3 2 1 5
C
D
4 6 7 8
A
B
SHEET 1 OF 1 SCALE:
TITLE:
MATERIAL:
DATE SIGNATURE
NAME
DEBUR AND
BREAK SHARP
EDGES
FINISH:
UNLESS OTHERWISE SPECIFIED:
DIMENSIONS ARE IN MILLIMETERS
SURFACE FINISH:
TOLERANCES:
LINEAR:
ANGULAR:
Q.A
MFG
APPV'D
CHK'D
DRAWN
WEIGHT:
WALLPACK LIGHT
MOUNTING INSTRUCTIONS:
1. Unscrew the four screws from the front of the xture to remove
lens frame and lens (FIG. 1)
2. Remove mounting plate (FIG. 2)
3. Place back gasket pad between mounting plate and j-box (not
provided), pull wires through center hole of mounting plate (FIG. 3)
4. Connect xture leads to supply leads (see wiring diagram for
standard and dimming wiring)
5. Install mounting plate over j-box with four screws
8.70’’ x 8.40’’ x 9.20’’
MOUNTING INSTRUCTIONS
SUITABLE FOR WATTAGES: 20W
MOUNTING PLATE
D
E
F
C
1 2 3 4
B
A
3 2 1 5
C
D
4 6 7 8
A
B
SHEET 1 OF 1 SCALE:
TITLE:
MATERIAL:
DATE SIGNATURE
NAME
DEBUR AND
BREAK SHARP
EDGES
FINISH:
UNLESS OTHERWISE SPECIFIED:
DIMENSIONS ARE IN MILLIMETERS
SURFACE FINISH:
TOLERANCES:
LINEAR:
ANGULAR:
Q.A
MFG
APPV'D
CHK'D
DRAWN
WEIGHT:
D
E
F
C
1 2 3 4
B
A
3 2 1 5
C
D
4 6 7 8
A
B
SHEET 1 OF 1 SCALE:
TITLE:
MATERIAL:
DATE SIGNATURE
NAME
DEBUR AND
BREAK SHARP
EDGES
FINISH:
UNLESS OTHERWISE SPECIFIED:
DIMENSIONS ARE IN MILLIMETERS
SURFACE FINISH:
TOLERANCES:
LINEAR:
ANGULAR:
Q.A
MFG
APPV'D
CHK'D
DRAWN
WEIGHT:
D
E
F
C
1 2 3 4
B
A
3 2 1 5
C
D
4 6 7 8
A
B
SHEET 1 OF 1 SCALE:
TITLE:
MATERIAL:
DATE SIGNATURE
NAME
DEBUR AND
BREAK SHARP
EDGES
FINISH:
UNLESS OTHERWISE SPECIFIED:
DIMENSIONS ARE IN MILLIMETERS
SURFACE FINISH:
TOLERANCES:
LINEAR:
ANGULAR:
Q.A
MFG
APPV'D
CHK'D
DRAWN
WEIGHT:
FIGURE 1
FIGURE 2
FIGURE 3
FIGURE 4
VER01.16
FIXTURE IS SUITABLE FOR WET LOCATION
CAUTION: For proper weatherproof function all gaskets must be seated properly and all screws inserted and tightened rmly. Apply
weatherproof silicone sealant (NOT included) around the edge of the Wall Box and/or Junction Box. This is especially important with an
uneven wall surface. Silicone all plugs and unused conduit entries.
IMPORTANT: READ BEFORE REMOVING FIXTURE FROM CARTON. RETAIN FOR FUTURE REFERENCE.
This xture must be wired and installed in accordance with the NATIONAL ELECTRIAL CODE and all state and applicable local codes and
ordinances. These codes and ordinances supersede any and all instruction contained herein. Installation should be performed only by a
licensed and bonded electrician and a person familiar with the construction and operation of the product and the hazards involved in the
installation and operation of this product. Proper grounding is required for safety. Make certain power is OFF before installing or maintaining
xture. Failure to do so may increase the RISK OF PERSONAL INJURY, PROPERTY DAMAGE, FIRE, AND DEATH. The manufacturer takes no
responsibility for the product not installed under those guidelines and those contained in this document. See wiring diagram on back
9.20 in
235 mm
8.70 in
222 mm
9.20 in
235 mm
8.70 in
222 mm
8.40 in
214 mm