Shoe Cabinet Width-23.62inch Depth-9.44inch Height-47.
! Safety and Care Advice Important – Please read these instructions fully before starting assembly • Check you have all the components and tools listed on the following pages. • During assembly do not stand or put weight on the product, this could cause damage. • Remove all fittings from the plastic bags and separate them into their groups. • Assemble the item as close to its final position (in the same room) as possible.
Components-Fittings Please check you have all the panels listed below Note:The quantitie below are the correcet amount to complete the assembly.In some cases more fittings may be supplied than are required. A B Cam Bolt x 30+2 E E1 C Cam Lock x 30+2 F D 8*30mm Dowel x 4+1 Shake hands x 6+1 H G E2 200mm Drawer slide x 1 3.5*14mm Screw x 32+2 3.
UsingCamlocks Camlocks Using 这一步文字确保客人可以看清 Step11 Step Connect the male camlock as diected in the assembly Connect the male as diectinStep 1structions usingcamlock a ed in the assembly instructions using scewdriver. 1 DO NOT OVER TIGHTEN. NE PAS SERRER EXCESSIVEMENT. 4 a scewdriver. Step Step 2 2 2 Push the male camlock into the entry hole. 按照实际的 安装方式更 改安装流 程，左边呈 现的是无预 埋件的安装 方式 Push the male camlock into the entry hole. Step 3 Step 3 Insert the female camlock as shown in the instruction.
Assembly Instructions 8 5 2 3 7 7 1 3 10 11 12 6 9 13 4 16 16 16 15 16 14 14 15 4
Assembly Instructions Step 1 K M 2 K M 1 K M Shoe rack stopper x 4 Shoe rack inner pivot x 4 Step 2 3 5 3 A 4 6 A A A Cam Bolt x 10 A 1 A 5
Assembly Instructions Step 3 3 B B B 1 B B B Cam Lock x 10 Step 4 7 7 1 6
Assembly Instructions A Step 5 A A 2 A A A Cam Bolt x 10 Step 6 2 7 7 1 7
Assembly Instructions B Step 7 B 2 B B B 1 B Cam Lock x 10 Step 8 E2 2 F E2 1 E2 E1 E2 The second round hole from the right F E2 200mm Drawer slide x 2 F 3.
Assembly Instructions Step 9 8 A C C A A C A C 8*30mm Dowel x 4 A Cam Bolt x 6 Step 10 B B 8 B B B Cam Lock x 6 9
Assembly Instructions Step 11 G 10 11 9 G 9 12 A 13 A D B B G 3.
Assembly Instructions Step 12 E1 F E1 F E1 F 200mm Drawer slide x 2 3.5*14mm Screw x 4 Step 13 X2 F 16 F J J 15 F 14 F 14 16 15 14 D X2 D D Shake hands x 4 F 3.
Assembly Instructions Step 14 8 H L L Shoe frame outer pivot x 4 H 4*11mm Screw x 4 Step 15 8 F 17 F F 17 F F 3.
Assembly Instructions Step 16 Step 17 N N R N Backboard buckle x 4 13
Assembly Instructions Step 18 Type1 P Type2 Type3 This is anti-dumping belt that fix the product to the wall and it can be used or not follow your needs. If it is a solid wall, please use expansion and self-tapping screws, if it is a wooden wall, only use self-tapping screws, please do not overtighten the screws.
Assembly Instructions Step 19 15
