Instructions / Assembly

MSP 48” Dining Table / Glass Table Top
Table Assembly Instructions
*WARNING* Heavy! Handle with care! Keep children away from assembly area!
Tools Required: Adjustable wrench and Slotted screwdriver (- minus driver).
Part List:
Table Top 1pcs
Table Legs w/adj. leveling pads 4pcs
Center Plate 1pcs
M8 Slotted stud bolts (Headless) 8pcs
8 Lock Washers and Nuts 8sets
20 Flat Washer 8pcs
M6 Slotted bolts 4pcs
6 Flat Washer, Lock Washer and Nut 4sets
Assembly Instructions:
It is suggested that you assemble product on a soft surface to avoid any damage to the finish.
1st. Place the table top on a soft surface upside down. Thread the M8 slotted stud bolts into the predrilled and tapped holes
in the table top. Using a slotted screw driver tighten the M8 slotted stud bolts. Do not over tighten as damage or
thread stripping could occur. Next attach the Table Legs to the Table Top by aligning the (2) thru holes in the Table
Leg with the M8 slotted stud bolts and sliding them thru the holes in the Table Legs. Place a 20 Flat Washer, a 8 Lock
Washer and Nut in this order onto each of the M8 slotted stud bolts. Only hand tighten each nut at this point. Repeat
this process for the (3) remaining legs.
2nd. Insert the (4) M6 Slotted Bolts into the (4) predrilled thru holes of the Center Plate. Align the (4) M6 Slotted Bolts in the
Center Plate with the (4) predrilled thru hole in the (4) Table Legs Center Plate support tabs, then slip the bolts thru the
holes. Place a 6 Flat Washer, a Lock Washer and a Nut in this order onto each of the (4) M6 Slotted Bolts. Only hand
tighten the nuts at this time.
3rd. Stand the table upright. Place the table onto a flat level surface. Align the Table Top, Center Plate and Table Legs so
the table is level and the legs are evenly spaced. Using an adjustable wrench tighten all of the nuts until the table is
firmly assembled and level. Do not over tighten the nut as damage or breakage my occur. You may also use the
adjustable leveling pad at the bottom of each leg to more finely level the table if needed.
4th. Finally move the table to desired location and carefully place the glass to into the table top. Do not drop the glass top
into the table top as breakage may occur. It is recommended that you place one side of the glass down first and then
lower the other side from underneath.
Caution – This table is constructed of cast metal and is brittle. Never force any part of the assembly and do not
over-tighten the fasteners, severe damage may occur.
Oxidation of cast iron: The cast iron component of the product is finished with a powder coating process that protects the iron from
rusting. However, due to the nature of the iron, rusting is inevitable. It is recommended that the consumer touch up any surface that is
scratched or damaged due to wear and tear. Applying an epoxy clear coating is recommended once a year.
Aluminum: The products with aluminum components please be reminded that aluminum is soft metal it is therefore necessary to
exercise caution when tightening nuts/bolts/screws on aluminum parts to prevent damaging the treads on the metal.
Solid Brass Fasteners: The fasteners provided are made with solid brass. This item will tarnish after weathering. A brass polish can be
use to keep the screws shiny or you can leave it untouched to give it a patina/antique look.
Weathering of wood: The wood component of the product is treated with a penetrating oil stain that is designed to protect from the
elements. However, it is recommended to re-stain the wood once a year (depending on the weather conditions in your area) to restore the
beauty of the product and to prolong the life of the wood.
Please do not return product to place of purchase – for customer service issues please call 1-248-
652-1404 to speak with customer service between the hours of 9am and 5pm Eastern Standard Time
or E-Mail any questions or comments to [e-mail]
2016-20040909