Instructions / Assembly

ManualsBrandsUnbranded ManualsAlcove Shower DoorsGridscape Series 28 in. x 80 in. Factory Window Framed Fixed Shower Screen in Black and Clear Glass without Handle

GRIDSCAPE FIXED PANEL

INSTALLATION INSTRUCTIONS – FULL DIVIDED-LIGHT

PREPARATION

Approximate Installation Time: 30 minutes

Tools Required for Installation:

➢ Chop Saw or Hacksaw

➢ Electric Drill

➢ 3/16” Masonry Drill Bit

➢ 9/64” Metal Drill Bit

➢ Philips Bit

➢ Pencil / Felt Tip Pen

➢ Safety Glasses

➢ Measuring Tape

➢ Masking Tape

➢ Level

➢ Rubber Mallet

➢ Clear Caulking or Sealant

QUESTIONS

Before beginning installation of product, make sure all parts are present. Compare parts with package contents list

and diagram below. Grid appearance may differ from images shown. If any part is missing or damaged, do not

attempt to install the product.

Please call our customer service department at 1-800-874-8601, 8 am - 5 pm EST, Monday to Friday.

Rev. 07/01/2018

Summary of content (7 pages)

PAGE 1
GRIDSCAPE FIXED PANEL INSTALLATION INSTRUCTIONS – FULL DIVIDED-LIGHT PREPARATION Approximate Installation Time: 30 minutes Tools Required for Installation: ➢ ➢ ➢ ➢ ➢ ➢ ➢ Chop Saw or Hacksaw Electric Drill 3/16” Masonry Drill Bit 9/64” Metal Drill Bit Philips Bit Pencil / Felt Tip Pen Safety Glasses ➢ ➢ ➢ ➢ ➢ Measuring Tape Masking Tape Level Rubber Mallet Clear Caulking or Sealant QUESTIONS Before beginning installation of product, make sure all parts are present.
PAGE 2
GRIDSCAPE FIXED PANEL INSTALLATION INSTRUCTIONS – FULL DIVIDED-LIGHT PACKAGE CONTENTS CST 998 Sill 1 CST 956 Wall Jamb 1 CST 952 Panel Snap Cover 1 Plastic Screw Anchor 8 Installation Screw (#8 x 1-1/4”) 8 834QO Panel Adjustment Screw (#8 x 3/4”) 6 CP967B Sill End Cap 1 Panel Assembly 1 1329 6-8114PHP - 2
PAGE 3
GRIDSCAPE FIXED PANEL INSTALLATION INSTRUCTIONS – FULL DIVIDED-LIGHT CST 956 CST 952 834QO (3x) 1329 (5x) 6-8114PHP (5x) (5x) PANEL 834QO (3x) * 6-8114PHP (3x) (5x) 1329 (3x) CST 998 CP967B * Note: Securing Sill CST 998 to curb / floor with screws is optional.
PAGE 4
GRIDSCAPE FIXED PANEL INSTALLATION INSTRUCTIONS – FULL DIVIDED-LIGHT STEP 1. IDENTIFY PANEL LOCATION AT LEFT OR RIGHT PANEL TO LEFT PANEL TO RIGHT STEP 2. MARK CENTERLINE AND POSITION SILL ON CURB ➢ Strike a centerline on the curb where the unit will sit. ➢ Position the Sill CST 998 on the centerline against the wall with the weep holes to the interior. Temporarily tape in place.
PAGE 5
GRIDSCAPE FIXED PANEL INSTALLATION INSTRUCTIONS – FULL DIVIDED-LIGHT STEP 3. INSTALL WALL JAMB PLUMB CST 956 CST 998 ➢ Set the Wall Jamb CST 956 into the Sill CST 998 and up against the wall. ➢ While holding the Jamb plumb with a level, use the pre-drilled holes in the Jamb to pencil mark (5) hole locations on the wall. ➢ Remove the Jamb and drill installation holes 1-1/2” deep using a 3/16” masonry bit. Insert Plastic Screw Anchors 1329 into the holes.
PAGE 6
GRIDSCAPE FIXED PANEL INSTALLATION INSTRUCTIONS – FULL DIVIDED-LIGHT STEP 5. SET SILL AND * SECURE TO CURB (*OPTIONAL) ➢ Place the Sill CST 998 on the curb centerline with weep holes to the inside of the enclosure. Push the Sill against the wall under the Wall Jamb CST 956. CST 956 ➢ ➢ ➢ ➢ ➢ 6-8114PHP (3x) *OPTIONAL OPTIONAL: Secure Sill to curb with Screws. Drill 3/16” holes through the Sill at (3) pre-drilled 3/8” holes in the Sill.
PAGE 7
GRIDSCAPE FIXED PANEL INSTALLATION INSTRUCTIONS – FULL DIVIDED-LIGHT STEP 7. SECURE PANEL FROM INTERIOR 5” 9/64” PILOT HOLES CENTER ➢ Secure the Panel from the interior of the enclosure using Panel Adjustment Screws 834QO (#8 x 3/4” Pan Head Combo Drive (Black Head)). Drill 9/64” pilot holes 3/4” deep at each Screw location. ➢ Secure the Panel to the Wall Jamb CST 956 with (3) Screws at top, middle and bottom. Locate Screws at 1/4” from the edge of the Panel.