Data Sheet

3
Rev. 2/21
The Groundsmaster
®
7200 and 7210 are manufactured
in Tomah, WI, ISO 9002 Certified Plant.
Groundsmaster
®
7200 Series Specifications
*
(continued)
* Specifications and design subject to change without notice. Products depicted in this literature are for demonstration purposes
only. Actual products offered for sale may vary in use, design, required attachments and safety features. See distributor for details
on all warranties.
** Assumes 8 mph mow speed, no overlap and 100% efficiency.
CUTTING DECKS (SOLD SEPARATELY)
CUTTING DECK
CONFIGURATIONS
62"
DECK W/
GUARDIAN® RECYCLER
KIT
62" DECK
W/ REAR DISCHARGE
KIT
72" DECK
W/GUARDIAN® KIT OR
FINE CUT GUARDIAN®
KIT
72" SIDE
DISCHARGE*
72" DECK
W/REAR DISCHARGE
KIT
60" SIDE
DISCHARGE
DECK MODEL NUMBER
30457 30457 30353 30481 30353 30456
COMPLETION KIT
(BLADES AND BAFFLES)
30306 30469 30304 or 30346 NA 30549 NA
WIDTH OF CUT
62" (158 cm) 62" (158 cm) 72" (182.8 cm) 72" (182.8 cm) 72" (182.8 cm) 60” (152.4 cm)
BLADE TIP SPEED
(@3250 ENGINE RPM)
16,000±1,000 ft./min. 16,000±1,000 ft./min. 16,000±1,000 ft./min. 18,000±1,000 ft./min. 16,000±1,000 ft./min. 18,000±1,000 ft./min.
5/16” THICK RUBBER
DISCHARGE CHUTE
NA Yes NA Yes Yes Yes
CUTTING DECK DEPTH
4.25" (10.8 cm) 4.25" (10.8 cm) 4.25" (10.8 cm) 5.5" (13.9 cm) 4.25" (10.8 cm) 5.5" (13.9 cm)
DECK ANTI-SCALP ROLLERS
4 4 4 5 4 5
BUMPER SKIDS
2 2 2 1 2 1
LEAF MULCHING KIT
NA NA NA PN 108-5273 NA NA
STRIPING KIT
NA NA NA 105-7273 NA NA
RECYCLER KIT
NA NA NA 30347 NA 30348
TALL GRASS BAFFLE KIT
PN 105-7269 PN 105-7269 PN 105-7269 NA PN 105-7269 NA
MEDIUM FLOW BLADE
NA NA NA PN 110-0621-03 NA PN 110-4701-03
HIGH FLOW BLADE
NA NA NA PN 110-0622-03 NA PN 110-4702-03
ATOMIC MULCHING BLADE
NA PN 107-0214-03 NA PN 110-0624-03 NA PN 110-4703-03
FLAT BLADE
NA NA NA NA PN 112-9586 NA
STANDARD BLADE
PN 92-5608-03 PN 92-5608-03 PN 108-1958 NA PN 108-1958 NA
BLADE AND BELT KIT
PN 105-7270 PN 105-7270 PN 105-7271 PN 105-7272 PN 105-7271 NA
MOWING RATE (ACRES/HR)**
4.9 4.9 5.8 5.8 5.8 4.8
SHIPPING WEIGHT
424 lb.. (192 kg.) 424 lb.. (192 kg.) 472 lb.. (214 kg.) 600 lb.. (272 kg.) 472 lb.. (214 kg.) 525 lb.. (238 kg.)
HEIGHT OF CUT
1”-6” (25 - 152 mm) adjustable in 0.25” (6 mm) increments.
60” & 72” SIDE DISCHARGE
DECK CONSTRUCTION
7-gauge (4.5 mm) 5.5” steel (14 cm) deep; welded deck with grass discharged on the right side. An 5/16” (8 mm) thick rubber discharge chute covers the discharge
opening to limit the throw distance of clippings.
62” & 72” BASE DECK
CONSTRUCTION
7-gauge (4.5 mm) 4.25” steel (11 cm) deep; welded deck. Requires Guardian® Recycler® or rear discharge completion kit.
FINE CUT GUARDIAN®
RECYCLER COMPLETION KIT
Three deflectors inside the chamber redirect clippings that are elevated in the chambers so that they are cut and re-cut. Deck chambers prevent throwing of objects
out from deck.
SPINDLE ASSEMBLY
Ductile cast iron 9" (23 cm) diameter conical spindle housing; Dual greaseable tapered roller bearings; Spindle shaft is 1.25" (3.2 cm) diameter, solid cold finished
steel, splined connection between spindle shaft and pulley; Welded blade retainer plus anti-scalp cups.
CUTTER DRIVE
Isolation mounted, splined PTO-driven gearbox transfers power to three separate spindles via two separate "B" section belts.
BLADES
Three 0.25” (6 mm) thick, 2.5” (63 mm) wide, heat-treated steel blades.
DECK SUSPENSION
Frame which supports deck via 4 vertically suspended chains. Front drag links provide fore/aft and left/right stability. Hydraulic deck lift includes load holding check
valves and gravity lower. Weight transfer system consisting of two torsion springs counterbalances some cutting deck weight to reduce turf damage.
BELT IDLER
Spring-loaded (torsion) idler.
DECK SKID
Replaceable, bolt-on, non-marking UHMW skid on both sides for Base decks and on left side on side discharge decks. Interchangeable left to right on base decks.
ANTI-SCALP CUPS
Anti-scalp cup located on each blade spindle.