Data Sheet

2
Rev. 2/22
The Groundsmaster 3500-D is manufactured
in Tomah, WI ISO 9002 Certified Plant.
Groundsmaster
®
3500 -D Specifications
*
* Specifications and design subject to change without notice. Products depicted in this literature are for demonstration purposes only.
Actual products offered for sale may vary in use, design, required attachments and safety features. See distributor for details on all warranties.
***Assumes max mow speed and 100% efficiency. Actual mowing rates may vary depending on operator and conditions.
GROUNDSMASTER 3500-D, MODEL 30807
ENGINE
Kubota® 3-cylinder, liquid-cooled diesel. Power: 24.8 hp (18.5 kW) gross, at rated speed of 3000 rpm. Torque peak: 52.7 ft∙lb (71.5 N∙m) @ 2200 rpm. Displacement:
1123cc. Remote-mounted 5" Donaldson
®
air cleaner. Fuel filter/water separator. Oil capacity 4 quarts (3.8 liters) with standard oil filter. Rear-mounted, cross flow 4-row
radiator. EPA Tier IV Final and Stage V compliant.
FUEL CAPACITY
11 gallons (42 liters). Biodiesel-Ready for use up to B-20 (20% biodiesel and 80% petroleum blend).
CONFIGURATION
Rear mounted engine, front operator position. Two post ROPS, seat belt and slope indicator standard. Sidewinder® cutting unit system.
TRACTION DRIVE
3-wheel drive in mow and transport. Series/Parallel™ hydrostatic, closed-loop transmission provides infinitely variable ground speed in forward and reverse. Variable
displacement piston type pump.
GROUND SPEED/CLEARANCE
Mow: 0-6 mph (0-10 km/h), mow speed is factory preset at 6 mph but is adjustable; Transport: 0-9 mph (0-14 km/h);
Reverse: 0-4 mph (0-6 km/h). Ground Clearance: 6" (15.3 cm).
CONTROLS
Forward and reverse traction control pedals; mow/transport foot lever; hand activated parking brake; hand operated ignition key switch; tilt steering wheel lock; PTO
switch; throttle; joystick control for deck raise and lower; cutting deck transport lock.
GAUGES & DIAGNOSTICS
Fuel gauge and hour meter, light cluster with glow plug and charge indicator lights, low engine oil pressure and high coolant temperature warning lights (high
temperature safety shut off).
ELECTRICAL & INTERLOCKS
Traction pedal, operator presence in seat, PTO engage or disengage, and cutting deck mow or transport safety interlock switches. Parking brake set prohibits
movement through traction pedal. 40 amp alternator and 12-volt, 585 CCA battery.
HYDRAULICS
Open center, manual valves, gear pump hydraulic system. System capacity approximately 3.5 gallon (13.2 liter) reservoir.
STEERING
Hydraulic power steering, tilt wheel.
TIRES/WHEELS
20 x 10-10, 4-ply rating, Turf Tread rear tire. 20 x 12-10, 4-ply rating, Turf Tread Fronts.
BRAKES
Dynamic through hydrostatic transmission service brake. Hand actuated over center, drum type parking brake.
OVERALL DIMENSIONS
Height Length Width Wheelbase
76" (193 cm) with ROPS 116" (295 cm) 71.8" (182 cm) with 68" (173 cm) WOC 59.5" (151 cm)
75.8" (193 cm) with 72" (183 cm) WOC - optional
WEIGHT
2,110 lbs. (957 kg) with cutting units.
WARRANTY
Two-year limited warranty. Refer to operator’s manual for further details.
CERTIFICATION
Complies with ANSI B71.4-2017 and EN5395.
CUTTING DECKS
TYPE
3 Contour™ Plus 27" (69 cm) rear-discharge rotary with standard full-length striping rear rollers on each deck. Sidewinder® system allows all three decks to slide
right and left 12" (30 cm) of center, 24" (61 cm) total travel. Mulching kit optional.
WIDTH OF CUT
68" (173 cm), standard and 72" (183 cm) optional. Deck overhang for trimming is 12" (30.5 cm) at 68" (173 cm) width of cut and 14" (35 cm) at 72" (183 cm). Overlap:
4.5" (11.4 cm) at standard width of cut.
HEIGHT OF CUT
0.75"-4" (1.9-10.2 cm) in 0.25" (.6 cm) increments. 3-position 0.030” (0.08 cm) incremental calibration
MOWING RATE**
At 68" (173 cm) width of cut, 4.1 acres/hr (1.7 hectares/hr)
CONSTRUCTION
10-gauge steel constructed chambers with 12-gauge welded reinforcements. Heavy-duty exoskeleton deck carrier frame, 1.5" (3.8 cm) square x .25" (.6 cm) wall
tube with 7-gauge side supports protects deck shell from impact damage. Spindle support 3/16" (.48 cm) high-strength steel and 10-gauge exterior channels.
SPINDLE ASSEMBLY
Ductile cast iron spindle housing. Dual greaseable tapered roller bearings. 1.25" (3.2 cm) diameter solid cold finished steel spindle shaft. Splined connection
between spindle shaft and deck motor. Welded blade retainer plus anti-scalp cups
GROUND FOLLOWING
6" (15 cm) anti-scalp cups on each blade.
TRACTION UNIT ACCESSORIES
31696 Work Light Kit
30669 Universal Sunshade - White
30671 Universal Sunshade - Red
30358 Bimini Canvas Sunshade
03614 Golf Ball Operator Guard
CUTTING DECK ACCESSORIES
104-5183 High Lift Blade
105-9810-03 Angle Sail Blade
107-0235-03 Atomic Blade
108-9026 Combo Blade
30836 Leaf Mulching Kit
137-6145 Sectional Rear Roller 27" (68.5 cm)
104-5168 Roller Scraper Kit