Data Sheet

4
Rev. 01/21
The Greensmaster 3250-D is manufactured
in Tomah, WI ISO 9002 Certified Plant.
Greensmaster
®
3250-D Specifications
*
* Specifications and design subject to change without notice. Products depicted in this literature are for demonstration purposes only.
Actual products offered for sale may vary in use, design, required attachments and safety features. Consult your local Toro Distributor.
GREENSMASTER 3250-D, MODEL 04384
ENGINE
Kubota® 902 tier 4i, 3-cylinder liquid-cooled diesel engine. 55.0 cu. in. (902 cc). Full pressure lubrication, oil filter. 24.8 hp (18.5 kW) @ 3600 rpm. Engine governed
to 2760 rpm high idle, 1500 rpm low idle (no load).
FUEL CAPACITY
6 gallons (22.7 liters). Biodiesel-Ready for use up to B-20 (20% biodiesel and 80% petroleum blend).
TRACTION DRIVE
Hydraulic piston pump, closed loop system. 2WD Parallel Hydrostatic or optional 3WD Series Parallel piston pump closed loop system. Foot pedal forward and reverse; infinitely variable.
GROUND SPEED
Forward-mowing speed is variable from 2-5 mph (3.2-8 km/h), adjusted by stop on pedal mechanism. Mow speed setting does not affect transport speed. Maximum
Greensmaster 3250-D transport speed is 8.8 mph (14.4 km/h), may be reduced by adjusting stop in footrest pan without affecting mow speeds.
TURF COMPACTION
8-12 psi (.55-.83 bar) average at recommended minimum tire pressures, with a 200 lb.. operator, and cutting units down.
STEERING
Power steering. No-tool quick adjust steering arm position, with arm motion allowing a wide range of operator sizes. Steering cylinder has through shaft design for
precise straight line tracking.
CONTROLS/GAUGES
Raise/lower-mow lever. Functional control lever (neutral, mow, transport). Foot operated traction drive and brakes. Hour meter
and warning light cluster. Hand operated choke, throttle. Mechanical engine speed control.
ELECTRICAL FEATURES
Maintenance-free 12-volt battery with 530 minimum cold cranking amps at 0° F. 40 amp alternator, circuit fused at 40 amps. Ignition switch/key. Seat switch. High
temperature engine kill override switch. Harness terminals, fuse slot, and console switch location available for optional lights installation.
SOUND LEVEL
84 dBA at operator ear under normal conditions.
OVERALL DIMENSIONS
Width of Cut: 59.0" (150 cm) Overall Height: 77.5" (197 cm)
Wheel Tread: 50.5" (128 cm) Net Weight (no fuel, no operator): 1,216 lbs. (552 kg)
Wheel Base: 48.6" (123 cm) Reel Speed: Approx.1,950 rpm @ 2760 rpm (Adjustable)
Overall Length (w/baskets): 93.9" (238 cm)
Overall Width: 68.0" (173 cm)
TIRES
Three 19 x 10.5-8, 2 ply pneumatic tubeless demountable and interchangeable. Smooth tread (approx. 1290 rev/mile). 8-12 psi front; 8-15 psi rear.
LEAK DETECTION
Turf Guardian™ optional.
BACKLAPPING
Standard equipment.
BRAKES
Foot activated 6" (15.2 cm) drum type mechanical with rack and pawl lock for parking.
SEAT
Contour seat with high backrest. 7" (17.8 cm) fore/aft slider adjustment with two mounting positions, allowing 9" (22.8 cm) total seat travel. Operator manual tube
mounted on the seat back for easy access.
ROPS
Roll over protection system standard.
CERTIFICATION
Certified to meet ANSI specification B71.4-2012 and European CE standards with appropriate kits installed.
WARRANTY
Two-year limited warranty. Refer to the Operator’s Manual for further details.
8 BLADE DPA CUTTING UNITS 11-BLADE DPA CUTTING UNITS 14-BLADE CUTTING UNITS
TRACTOR
These cutting units will mount on any Toro riding Greensmaster (excluding Greensmaster TriFlex models).
HEIGHT OF CUT (HOC) RANGE
Cutting height is adjusted on front roller by two vertical screws and held by two locking cap screws. Bench HOC range is .062"-.297" (1.6-7.5 mm). With high HOC kit,
range is .297-1.0" (7.5-25.4 mm). Effective HOC may vary depending on turf conditions and bedknife installed.
REEL WELDMENT
Reels are 5" (13 cm) in diameter, 21" (53.3 cm) in length. EdgeSeries™ Reels blades are welded to 5 stamped steel spiders, and heat treated. The reel is ground for
diameter and concentricity, and backgrind.
REEL BEARINGS
Two stainless steel ball bearings, 30 mm inside diameter slip fit onto reel shaft retained by internally splined threaded insert. Low drag seals/slingers for added
protection with o-ring sealed motor and counterweight. Reel position maintained by a wave washer with no adjusting nut.
MAINTENANCE
No grease zerks, sealed bearing design eliminates daily maintenance.
REEL DRIVE
The reel weldment shaft is a 1.375" (35 mm) diameter tube with internally splined threaded insert.
FRAME
Precision machined, die-cast aluminum cross member with two bolt-on die-cast aluminum side plates.
AGGRESSIVENESS
Aggressiveness stays constant throughout the life of the reel regardless of reel or bedknife wear. Patented design.
BEDKNIFE
Replaceable single edged EdgeMax
TM
Microcut Bedknife is standard.
BEDKNIFE ADJUSTMENT
Dual screw, indexed “click” adjustment to the reel; detents corresponding positively to .0007" (.018 mm) bedknife movement for each position.
FRONT & REAR ROLLERS
Front: Not included with cutting unit, purchased separately. Option between full, narrow-spaced and wide-spaced roller.
Rear: Steel full, 2" (5.1 cm) diameter with sealed bearings and through-shaft.
GRASS SHIELD
Non-adjustable shield with adjustable cut-off bar to improve grass discharge from reel in wet conditions.
TOTAL WEIGHT
8-blade: 72 lbs. (32.7 kg) with aluminum Wiehle Roller. 11-blade: 75 lbs. (34 kg) with aluminum Narrow Wiehle Roller. 14-blade: 78 lbs. (35 kg) with aluminum Wiehle Roller.