Data Sheet

2
Rev. 1/20
The Greensmaster
®
eTriFlex
TM
is manufactured in
Tomah, WI ISO 9002 Certified Plant.
Greensmaster
®
eTriFlex
™
3360/3370 Specifications
*
* Specifications and design subject to change without notice. Products depicted in this literature are for demonstration purposes only.
Actual products offered for sale may vary in use, design, required attachments and safety features. Consult your local Toro Distributor.
GREENSMASTER eTRIFLEX 3360, MODEL 04580 (ENGINE/GENERATOR) GREENSMASTER eTRIFLEX 3370, MODEL 04590 (LITHIUM-ION BATTERY)
POWER SOURCE
Engine: Kawasaki 14.5 HP (10.8 kW) @3600 rpm, gasoline, air-cooled, twin-
cylinder, governed to 2400 rpm, displacement 36.8 cu-inch (603cc). Choke
standard.
Generator: 48V 5400W air cooled brushless permanent magnet motor in parallel
with four 12V 33AH AGM batteries (connected in series). Generator is used to
start engine
Eight, Lithium-Ion Samsung® SDI batteries
ENERGY CAPACITY
4.9 gallons (18.5 liter) gasoline 10.77 kWh; 48V nominal
ELECTRICAL SYSTEMS
48V System for traction motor circuit, steering motor circuit, cutting unit motor circuit and lift / lower actuator circuit. 12V system for primary controls and brake
actuator.
DIAGNOSTICS
Basic machine diagnostics available through the InfoCenter™
POWER STEERING
48V electric steering motor with torque feedback device
TRACTION DRIVE
Positive 2WD traction drive: Two, brushless permanent magnet traction motors coupled to a gearbox. Optional 3WD. (patent-pending).
RDS™ SYSTEM
Radius Dependent Speeds – Clip Rate: Maintains consistent cutting unit clip rate in turns on each individual reel (patent-pending). Wheel Speed Control: Individual
wheel speed control during turns (patent-pending). Lift-In-Turn: Provides level cut from side to side of cutting units regardless of turning angle (patented).
GROUND SPEED
Mowing 0-5 mph (0-8 km/h); Transport 0-10 mph (0-16 km/h); Reverse 0-3 mph (0-4.8 km/h). Selective slow down feature for turning in mowing mode.
Automatic slow down at high transport speeds when turning.
CUTTING UNIT DRIVE
Three, 48V (1.1 KW), air-cooled brushless permanent magnet motors.
CUTTING UNIT LIFT SYSTEM
48V electric linear actuators with fully integrated brushless permanent magnet motor and controller. Fully sealed with splash guard. Center lift actuator drop and
raise delay is dependent on machine velocity.
VERTICUTTING
Yes No
BACKLAPPING
Adjustable from 200–520 RPM
CONTROLS
Traction Pedal: Forward/Neutral/Reverse; Joystick: Raise/Lower; Function control switch: Neutral, Mow, Transport; Key switch; Steering Arm Lock Pedal; Brake pedal;
Parking Brake; InfoCenter; Seat Adjusting Lever; Main Power Connectors; Choke (3360 only); Fuel-Shutoff Valve
INFOCENTER™
InfoCenter: Onboard LCD display shows gauges, alerts/faults, service reminders, electrical system diagnostics, low oil pressure, alternator, engine hours, engine rpm,
voltage, functional control status, parking brake applied, reel speed setting, backlap control, clip control, calibration of 48V components.
DIAGNOSTICS
Basic machine diagnostics available through the InfoCenter.
BRAKES
Traction motor regenerative braking; foot pedal service/parking brake, linear-actuated automatic parking brake.
TIRES/WHEELS/PRESSURES
Three, 19x10.5x8, 4-ply rating pneumatic tubeless and demountable. Smooth tread. Tire pressure 12–16 psi (83–110 kPa) front and rear.
WEIGHT, 11-BLADE CU,
BASKETS, AND STANDARD
SEAT, NO FUEL
Mow: 1,354 lbs (614 kg) Transport: 1,625 lbs (737 kg) Mow: 1,359 lbs (616 kg) Transport: 1,628 lbs (738 kg)
NOISE LEVEL (DBA)
Sound Power: 91 db(A)
Operator Ear: 73 db(A)
Bystander: 25ft – 78 db(A), 50ft – 73 db(A), 100ft – 66 db(A)
Sound Power: 82 db(A)
Operator Ear: 66 db(A)
GROUND CLEARANCE
3.8" (9.7cm) ground clearance. Three, tie down locations (2 side, 1 rear).
WIDTH OF CUT
59" (150cm)
CUTTING UNIT SUSPENSION
Double A-Arm Suspension utilizing sealed ball joints allows free cutting unit motion in pitch and yaw. Links system for the roll. The basket is directly mounted to the
cutting unit displacing weight evenly over front and rear rollers. (patented)
QUICK-CONNECT CUTTING UNITS
Snap-on cutting unit and reel motors (no tools required).
OPTIONAL ATTACHMENTS
8, 11, or 14-blade Cutting Units, Groomers, Rear Roller Brushes, Anti-Bobbing, Light Kit, Variety of Front Rollers, Thatching Reels, Tri-Roller, Spiker, Bobbing Kit,
Standard or Premium Seat, Wireless Hour Meter, Bimini Shade, Bag Kit, Spark Arrestor.
MAINTENANCE
No grease points
OVERALL DIMENSIONS
Width: 70.9" (180cm)
Length: with Baskets 98" (249cm)
Height: 80.8" (205cm)
Wheelbase: 49.8" (126.5cm)
Minimum Turning Radius (to machine center line): 35.9" (91cm)
CERTIFICATION
Meets ANSI B71.5–2017 and EU 2000. 14EC (noise), 2006/42/EC (machinery safety), 2014/53/EU (red)
WARRANTY
Two-year limited warranty, both models. Lithium-Ion battery 4 years (3rd and 4th year prorated). Refer to the Operator’s Manual for further details.