Installation Guide

ManualsBrandsUnbranded ManualsDisplay CabinetsFloor Standing Oak Lighted Curio Cabinet

ASSEMBLE GUIDE

MODEL FSCC2000MK-1

Note: This instruction booklet contains important safety information,

please read and keep for future reference.

JENLEA INC.

Summary of content (9 pages)

PAGE 1
ASSEMBLE GUIDE MODEL FSCC2000MK-1 Note: This instruction booklet contains important safety information, please read and keep for future reference. JENLEA INC.
PAGE 2
PARTS IDENTIFICATION --Ensure that all parts and components are located before beginning assembly. Parts are labeled to help distinguish similar parts from each other. Use this PARTS IDENTIFICATION sheet to help identify similar Parts. --Assemble on a soft surface to prevent damage to the product finish. --Two people are needed for assembly. --Estimated assembly time is approximately 1.5 hours.
PAGE 3
HARDWARE INDENTIFICATION (R1)LIGHT-1PC (R2)M6×30-8PCS (R3)M6×35-4PCS (R4)ST2.9×12-6PCS TOOL REQUIRED (R5)ST2.
PAGE 4
(R9)ADJUSTABLE FOOT:5PCS 1.Fasten 5 adjustable foot R9 to the back side of base unit A. R9=5 Note:The cabinet can be made level through adjusting the adjustable foot R9. NO.1 (R2)M6×30:4PCS 2.Fasten side panel BL&BR to base unit A, using 4 screw R2(M6×30). NO.
PAGE 5
(R3)M6×35:4PCS 3.Fit shelf board C to side panel BL&BR, then fasten top side panel DL&DR to shelf boar C and side panel BL&BR, using 4 screw R3 (M6×35). Note:when you assemble the cabinet. please note the arrow showes up direction of the SHELF BOARD C. NO.3 (R4)ST2.9×12:2PCS 4.a)Overturn cover board E. b)Fasten light R1 on cover board E with 2 screw R4 (ST2.9×12). NO.
PAGE 6
(R2)M6×30:4PCS Note:edges of two sides of the bar on cover board E must be on back of the top side panel DL&DR, after assembly, keep 3 parts at the same horizontal level. 5.a)Sliping down cover board E into the position to fit top side panel DL&DR into the grooves on cover board E. b)Fasten E to DL&DR with 4 screw R2(M6×30). NO.5 (R5)ST2.9×18:4PCS 6.a) Fit top back panel G and back panel F into grooves on base unit A, shelf board C and cover board E. b)Fasten G&F, using 4 screw R5(ST2.
PAGE 7
(R5)ST2.9×18:34PCS R5=34 7.Fit left and right back panel HL&HR, top left and right panel IL&IR into the grooves on base unit A, shelf board C and cover board E, fasten with 34 screw R5(ST2.9×18). NO.7 (R4)ST2.9×12:4PCS 8.Fasten plastic strap to middle of left and right back panel HL &HR, top left and right back panel IL&IR, using 4 screw R4(ST2.9×12). NO.
PAGE 8
(R6)SHELF SUPPORT STUD:15PCS 9.Fasten 15 shelf support R6 into the holes on back panel F, top back panel G, side panel BL&BR, top side panel DL&DR. NO.9 10.Slide shelf J onto shelf Support R6. NO.
PAGE 9
(R7)DOOR KNOB:2PCS (R8)POLE FOR HINGE:4PCS 11.a)Screw door knob R7 into holes on left of door and top door K&L. Slip L into place by lowering it over hinge on top right panel DR. b)Insert 2 pole for hinge R8 into holes on hinges for DR. c)Repeat process for door K. NO.11 (R10)PLASTIC SCREW ANCHOR:1PC 12.In order to ensure that the cabinet is stable adjust the adjustable foot R9 under the cabinet.