FR700V SERIES FUEL TRANSFER PUMPS Installation and Operation Manual MADE IN USA
| FR700V SERIES FUEL TRANSFER PUMPS Table of Contents Warranty Policy.................................................................2 Safety Information.............................................................3 Installation........................................................................3 Anti-Siphon Device............................................................5 Electrical Wiring................................................................6 Wiring Procedure............................
INSTALLATION AND OPERATION MANUAL About This Manual From initial concept and design through its final production, your Fill-Rite pump is built to give you years of trouble free use. To ensure it provides that service, it is critical that you read this entire manual prior to attempting to install or operate your new pump.
| FR700V SERIES FUEL TRANSFER PUMPS CAUTION! Threaded pipe joints and connections should be sealed with the appropriate sealant or sealant tape to minimize the possibility of leaks. SKID TANK INSTALLATION Typical Skid Tank Installation Materials • 1¼" pipe cut to a length that will extend to within 3" of the bottom of the tank when screwed into the tank adapter with the tank adapter screwed into the tank flange (see SKID TANK INSTALLATION diagram).
INSTALLATION AND OPERATION MANUAL CAUTION! Threaded pipe joints and connections should be sealed with the appropriate sealant or sealant tape to minimize the possibility of leaks. Anti-Siphon Device Your FR700V Series pump comes from the factory ready to install an anti-siphon tube back to the tank. An anti-siphon device (a.k.a. vacuum breaker) is important because it will break a liquid siphon if there is an open nozzle or a leaking hose below the fluid level in the tank when the pump is turned off.
| FR700V SERIES FUEL TRANSFER PUMPS Electrical Wiring WARNING! Electrical wiring should be performed ONLY by a licensed electrician in compliance with local, state, and national electrical code NEC/ANSI/NFPA 70, NFPA30, and NFPA 30A, as appropriate to the intended use of the pump. Threaded rigid conduit, sealed fittings, and conductor seal should be used. The pump must be properly grounded.
INSTALLATION AND OPERATION MANUAL Operating Instructions 1. Reset Meter to “0” (if applicable). 2. Remove dispensing nozzle from nozzle boot. Safety Testing Approvals The Fill-Rite line of pumps have been safety tested for compliance to the standards set forth by UL Laboratories. 3. Move the switch lever to the “ON” position to power the pump. 4. Insert the dispensing nozzle into the container to be filled. 5.
| FR700V SERIES FUEL TRANSFER PUMPS Accessories A wide variety of accessories are available to help you maximize the performance of your FR700V Series pump. Listed below are the applicable available accessories for your specific product. Please contact your authorized Fill-Rite distributor to purchase the accessories you need.
INSTALLATION AND OPERATION MANUAL Troubleshooting (continued) Symptom Fluid leakage Pump won't prime Low capacity Pump runs slowly Motor stalls Motor overheats Motor inoperative Pump hums but will not operate Cause Solution 1. Bad o-ring gasket Check all o-ring gaskets 2. Dirty shaft seal Clean seal & seal cavity 3. Bad shaft seal Replace seal 4. Incompatible fluid Refer wetted parts list to fluid manufacturer 5. Loose fasteners Tighten fasteners 1.
| FR700V SERIES FUEL TRANSFER PUMPS Replacement Parts Information For repairs or routine maintenance, Fill-Rite offers the parts you need. The following parts diagram and list covers all applicable parts for your Fill-Rite product. These parts can be obtained through any authorized Fill-Rite dealer. Be sure to use only genuine Fill-Rite replacement parts for your service and maintenance needs. For a list of authorized dealers, please visit our web site at www.fillrite.com.
INSTALLATION AND OPERATION MANUAL FR700V / FR701V / FR710V / FR711V Parts List 700KTF2659 KIT120NB KIT700CV KIT700RG KIT700SL KIT700SW KIT700SG KIT700BG 2 4 3 3 FR701V Parts List FR711V Parts List The FR701V configuration adds a 807C Series mechanical meter, inlet meter flange, outlet meter flange, the associated attaching hardware, and gaskets. This package is available in gallon or liter register.
ATTENTION! The following information is for suffix “E” pumps and meters (designed for use outside the United States and Canada)! Refer to the information label applied to your pump to see if it is applicable. Materials of Construction Materials of construction of the external surface of the unit are: painted steel; painted cast iron; painted aluminum; zinc plated steel. for products sold outside the US and Canada. Please refer to the tag on your particular product for its particular compliance data.